- Online trainings provide solutions to your design projects.
- Receive guidance from experienced Dlubal instructors.
- Gain valuable program insight, increase efficiency, and improve workflows.
- Virtual trainings are cost-effective, flexible, and convenient.
Eurocode 2 | Concrete Structures According to DIN EN 1992-1-1
Online Training Information
Why An Online Training?
Online group training sessions provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.
Date | Time
Event Language
EnglishContent
Online Training on Reinforced Concrete Design According to DIN EN 1992-1-1
In this training, the verification of reinforced concrete structures according to the DIN EN 1992-1-1 standard is explained using the structural analysis software RFEM and the relevant add-ons.
The add-ons for concrete design according to EC 2 will be explained using relevant examples. The ultimate limit state (ULS), serviceability limit state (ULS), stability analysis and punching shear design will be covered during the training session.
Price
250.00 EUR zzgl. MwSt.Time Schedule
| - |
Basic Information RFEM 6 introduction |
| - |
Load Combinations Load combinations for the ultimate and serviceability limit state designs |
| - |
Member Design Basics Design specifications for member structures
Evaluation of results |
| - |
Surface Design Basics Design specifications for surface structures Evaluation of results |
| - |
Punching Shear Design Punching shear design and specifications
Evaluation of results |
| - |
Serviceability Serviceability design for member and surface structures
|
| - |
Stability Analysis Stability checks according to nominal curvature method
|
| - | Tips & Tricks |
A reliable internet connection is required to participate. Basic user knowledge in RSTAB or RFEM is also required. The online training is carried out in RFEM and the associated add-ons.
During the training, each participant can ask questions via chat at any time.
Each participant will receive the following after the event:
- Participation certificate
- Training presentation (PDF)
- RFEM model examples
- Training video recording
This information will allow the participant to independently revisit the training step-by-step for further review.
In order to take part in the online training, the participant will automatically receive the login information after the event registration.
Speakers
Dipl.-Ing. (FH) Adrian Langhammer
Product Engineering & Customer Support
Mr. Langhammer is responsible for development in the area of reinforced concrete structures, and provides technical support to our customers.
Dipl.-Ing. (FH) Paul Kieloch
Product Engineering & Customer Support
Mr. Kieloch provides technical support to our customers and is responsible for development in the area of reinforced concrete structures.
Keywords
Online training Reinforced concrete design Eurocode 2 EC 2 Load capacity Serviceability Deformation calculation Nonlinear calculation Crack width Punching shear
Links
Write Comment...
Write Comment...
Contact Us
Do you have any questions about a group training course? Contact us via phone, email, chat, or forum.
If you are interested in a specific topic not included in a group training, consider an Individual Training.
Individual Training
★
★
★
★
★
Impressed by Program and Presentation
"I have watched the webinar recording "Design of Cross-laminated Timber Panels (CLT) According to Eurocode 5" on YouTube and I am impressed by about the program and the very good presentation.
Dipl.-Ing. Lothar Reichle
02/18/2020
When determining the minimum reinforcement for the serviceability limit state according to 7.3.2, the applied effective tensile strength fct,eff has a significant influence on the determined amount of reinforcement.
- In the RF‑CONCRETE Surfaces add-on module, I get a design failure for the serviceability limit state (SLS) and no values are displayed for the steel stresses. Also, Message 239) is displayed. Why?
-
How can I efficiently define line hinges on several surfaces?
- How do I create an imperfection based on a mode shape in RFEM 6?
- Although all the member design checks have been fulfilled, I get the "Not Covered Reinforcement" result. What is the reason?
- In RFEM 6, is it possible to display a graphic with the distribution of the required reinforcement in the DIN A0 format?
-
Where can I find the graphical results of punching shear in the concrete design? Especially the distribution of shear forces at the critical perimeter or the punching loads.
- Is it possible to display the reinforcement description in RFEM 6?
- Can I define a different bar size in the RFEM 6 Concrete Design add-on other than the default bar sizes available in the drop-down?
- Can the RFEM 6 Concrete Design add-on automatically design member and surface reinforcement?
- I would like to perform punching design of a floor slab. I have selected nodes for the design, but they are marked as invalid. Where did I make a mistake?
- Is it possible to display the reinforcement description in RFEM 6?
Recommended Products
RFEM 6
Main Program
The structural analysis program RFEM 6 is the basis of a modular software system. The main program RFEM 6 is used to define structures, materials, and loads of planar and spatial structural systems consisting of plates, walls, shells, and members. The program can also design combined structures as well as solid and contact elements.
Price of First License
4,450.00 EURSocial Networks
Frequently Visited Pages
- How do I create an imperfection based on a mode shape in RFEM 6?
