The automatic increment of a reinforcement for the deformation analysis is not possible. If the deformation calculation is based on the determination of the stiffness, it is not constructive to develop an algorithm that, for example, increases the reinforcement at the point of maximum deformation. Such a procedure would not result in reduction of the deformation.
Therefore, it is necessary to increase the reinforcement manually.
Knowledge Base
The reinforcement proposal from RF-/CONCRETE Members can be exported to Revit. The rectangular and circular cross-sections are currently supported.
The reinforcement bars can be modified retroactively in Revit.
DIN EN 1992-1-1/NA/A1:2015-12 (Germany) 
ÖNORM B 1992-1-1:2018-01 (Austria) 
NBN EN 1992-1-1 ANB:2010 (Belgium) 
BDS EN 1992-1-1:2005/NA:2011 (Bulgaria) 
EN 1992-1-1 DK NA:2013 (Denmark) 
NF EN 1992-1-1/NA:2016-03 (France) 
SFS EN 1992-1-1/NA:2007-10 (Finland) 
UNI EN 1992-1-1/NA:2007-07 (Italy) 
LVS EN 1992-1-1:2005/NA:2014 (Latvia) 
LST EN 1992-1-1:2005/NA:2011 (Lithuania) 
MS EN 1992-1-1:2010 (Malaysia) 
NEN-EN 1992-1-1+C2:2011/NB:2016 (Netherlands) 
NS EN 1992-1 -1:2004-NA:2008 (Norway) 
PN EN 1992-1-1/NA:2010 (Poland) 
NP EN 1992-1-1/NA:2010-02 (Portugal) 
SR EN 1992-1-1:2004/NA:2008 (Romania) 
SS EN 1992-1-1/NA:2008 (Sweden) 
SS EN 1992-1-1/NA:2008-06 (Singapore) 
STN EN 1992-1-1/NA:2008-06 (Slovakia) 
SIST EN 1992-1-1:2005/A101:2006 (Slovenia) 
UNE EN 1992-1-1/NA:2013 (Spain) 
CSN EN 1992-1-1/NA:2016-05 (Czech Republic) 
BS EN 1992-1-1:2004/NA:2005 (United Kingdom) 
TKP EN 1992-1-1:2009 (Belarus) 
CYS EN 1992-1-1:2004/NA:2009 (Cyprus) 
Main Program
The new generation of 3D FEA software is used for the structural analysis of members, surfaces, and solids.
Add-On
The Concrete Design add-on allows for various design checks according to international standards. You can design members, surfaces, and columns, as well as perform punching and deformation analyses.
Add-On
The Construction Stages Analysis (CSA) add-on allows for considering the construction process of structures (member, surface, and solid structures) in RFEM.
Add-On
In RFEM, the Geotechnical Analysis add-on uses properties from soil samples to determine the soil body to be analyzed. The accurate determination of soil conditions significantly affects the quality of the structural analysis of buildings.
Add-On
The Modal Analysis add-on allows for the calculation of eigenvalues, natural frequencies, and natural periods for member, surface, and solid models.
Add-On
The Response Spectrum Analysis add-on performs seismic analysis using multi-modal response spectrum analysis. The spectra required for this can be created in compliance with the standards or can be user-defined. The equivalent static forces are generated from them. The add-on includes an extensive library of accelerograms from seismic zones that can be used to generate the response spectra.
Add-On
Using the Pushover Analysis add-on, you can analyze the seismic actions on a particular building, and thus assess whether the building can withstand an earthquake.
Add-On
The Building Model add-on for RFEM allows you to define and manipulate a building using stories. The stories can be adjusted in many ways afterwards. The information about stories and the entire model (center of gravity) is displayed in tables and graphics.
Add-On
The Masonry Design add-on for RFEM allows you to design masonry using the finite element method. It was developed as part of the research project titled DDMaS – Digitizing the Design of Masonry Structures. The material model represents the nonlinear behavior of the brick-mortar combination in the form of macro-modeling.
