Section Classification in RFEM 6 According to EN 1993-1-1

Technical Article on the Topic Structural Analysis Using Dlubal Software

  • Knowledge Base

Technical Article

The design of cross-sections according to Eurocode 3 is based on the classification of the cross-section to be designed in terms of classes determined by the standard. The classification of cross-sections is important since it determines the limits of resistance and rotation capacity due to local buckling of cross-section parts. 

EN 1993-1‑1 [1] defines the following four cross-section classes (also shown in Image 1):

  • Class 1: cross-sections that can form a plastic hinge with the rotation capacity required for plastic analysis without reduction of the resistance
  • Class 2: cross-sections that can develop plastic moment resistance, but have limited rotation capacity because of local buckling
  • Class 3: cross-sections in which the calculated stress in the extreme compression fiber of the member can reach its proof strength, but local buckling is liable to prevent development of the full plastic moment resistance
  • Class 4 cross-sections are those in which local buckling will occur before the attainment of yield strength in one or more parts of the cross-section

The classification is done separately for all cross-section parts by comparing the provided width-to-thickness ratios to the limit values for each class as given by the standard. Thus, the class of each cross-section part is defined and the one with the least favorable value governs for the entire cross-section. The limit values depend on the following:

  • Support condition of cross-section parts (on one or both sides)
  • Yield strength of the steel used in the form of factor ε
  • Stress curve in cross-section parts
  • Magnitude of compressive strength

Eurocode 3 provides tables based on which the maximum width-to-thickness ratios for the cross-section parts can be calculated and compared to the limit values. For instance, the maximum width-to-thickness ratios to categorize an internal compression part as class 3 are determined by the factors shown in Image 2.

The limit value for internal parts subjected solely to compression or bending is determined by factor ε, which is related to the yield strength of the steel. For parts subjected to both bending and compression, on the other hand, the stress distribution is detected by parameter α (plastic, Classes 1 and 2) or ψ (elastic, Class 3). The former represents the percentage length of the compression stress in the cross-section part, while the latter represents the ratio of the boundary stresses (Image 3). Thus, in addition to factor ε, the limit value of the width-to-thickness ratios for parts subjected to bending and compression involves parameter α for classes 1 and 2 and parameter ψ for class 3.

Section Classification in RFEM 6

The Steel Design add-on offered in RFEM 6 for the design of steel structures performs a detailed cross-section classification on each design location before the design is carried out. The cross-section classification for each design check type is available in its associated design check details.

This is demonstrated for the beam shown in Image 4 (IPE 300, steel S355), for which the Steel Design add-on has been calculated and the results for each design type are already available. If, for instance, you display the design check details, you may notice that the cross-section classification is also provided in detail (Image 5).

As already explained, the classification is done separately for all cross-section parts (called subpanels in RFEM 6, five, in this case). Hence, different cross-section classes can be assigned to each subpanel, but the one with the least favorable value governs for the entire cross-section. In this manner, the cross-section of interest is classified as class 4 for the section proof according to 6.2.4, which is the cross-section class of subpanel number 3.

Since subpanel no. 3 is supported on both sides and is subjected to compression, its classification is done according to Table 5.2 from Eurocode 3 [1]. The yield strength of the steel is 355 N/mm2 and therefore, the value of factor ε is 0.814 (Image 5). Based on this factor, the limit values of the width-to-thickness ratios for classes 1, 2, and 3 are calculated (λ1, λ2, and λ3, respectively) according to the aforementioned table. Next, the c/t ratio is calculated on the basis of the length (c) and thickness (t) of the section part, and it is compared to the limit values for the cross-section classes. For this subpanel, the provided c/t ratio is larger than the one calculated for cross-section class 3 and therefore, class 4 is assigned to the subpanel. Given that the other subpanels are classified as class 1, this is the subpanel (for example, subpanel no. 3) with the least favorable value that governs for the entire cross section. On that account, the cross-section of interest is classified as class 4 for the section proof according to 6.2.4.

To better understand the cross-section classification, you can display the individual subpanels of the cross-section in the Subpanels tab of the Section Information window (Image 6).

Final Remarks

The cross-section classification in RFEM 6 for the design of steel members is carried out according to the provisions in Eurocode 3 [1]. The classification is done separately for all cross-section parts by comparing the provided width-to-thickness ratios to the limit values for each class as given by the standard. The limit values depend on the support condition of cross-section parts, yield strength of steel, stress curve in cross-section parts, and magnitude of compressive strength. Once calculated, the width-to-thickness ratio is compared to these and the class of each cross-section part is defined. Finally, the least favorable class obtained for the individual subpanels is assigned to the entire cross-section.

Author

Irena Kirova, M.Sc.

Irena Kirova, M.Sc.

Marketing & Customer Support

Ms. Kirova is responsible for creating technical articles and provides technical support to the Dlubal customers.

Keywords

Section classification Steel design Steel members

Reference

[1]   Eurocode 3: Design of steel structures - Part 1‑1: General rules and rules for buildings; EN 1993‑1‑1:2010‑12

Links

Write Comment...

Write Comment...

  • Views 683x
  • Updated 03/14/2022

Contact Us

Contact Dlubal

Do you have further questions or need advice? Contact us via phone, email, chat, or forum, or find suggested solutions and useful tips on our FAQ page, available 24/7.

(267) 702-2815

[email protected]

Online Training | English

RFEM 6 | Basics

Online Training 07/29/2022 9:00 AM - 1:00 PM CEST

Online Training | English

RFEM 6 | Basics | USA

Online Training 08/11/2022 12:00 PM - 4:00 PM EDT

Online Training | English

Eurocode 2 | Concrete Structures According to DIN EN 1992-1-1

Online Training 08/12/2022 8:30 AM - 12:30 PM CEST

Online Training | English

Eurocode 3 | Steel Structures According to DIN EN 1993-1-1

Online Training 09/08/2022 9:00 AM - 1:00 PM CEST

Online Training | English

Eurocode 5 | Timber Structures According to DIN EN 1995-1-1

Online Training 09/15/2022 9:00 AM - 1:00 PM CEST

Online Training | English

RFEM 6 | Dynamic Analysis and Seismic Design According to EC 8

Online Training 09/21/2022 9:00 AM - 1:00 PM CEST

Online Training | English

RFEM 6 | Basics

Online Training 10/07/2022 9:00 AM - 1:00 PM CEST

Online Training | English

Eurocode 2 | Concrete Structures According to DIN EN 1992-1-1

Online Training 10/14/2022 9:00 AM - 1:00 PM CEST

Online Training | English

Eurocode 3 | Steel Structures According to DIN EN 1993-1-1

Online Training 11/17/2022 9:00 AM - 1:00 PM CET

Online Training | English

RFEM 6 | Dynamic Analysis and Seismic Design According to EC 8

Online Training 11/23/2022 9:00 AM - 1:00 PM CET

Online Training | English

Eurocode 5 | Timber Structures According to DIN EN 1995-1-1

Online Training 12/08/2022 9:00 AM - 1:00 PM CET

CFD Wind Simulation with RWIND 2

CFD Wind Simulation with RWIND 2

Webinar 06/29/2022 2:00 PM - 3:00 PM EDT

Online Training | English

Eurocode 5 | Timber Structures According to DIN EN 1995-1-1

Online Training 06/15/2022 8:30 AM - 12:30 PM CEST

Online Training | English

RFEM 6 for Students | USA

Online Training 06/08/2022 1:00 PM - 4:00 PM EDT

ADM 2020 Aluminum Design in \n RFEM 6

ADM 2020 Aluminum Design in RFEM 6

Webinar 05/25/2022 2:00 PM - 3:00 PM EDT

Online Training | English

RFEM 6 | Students | Introduction to Timber Design

Online Training 05/25/2022 4:00 PM - 5:00 PM CEST

RFEM 6
Hall with Arched Roof

Main Program

RFEM 6 structural analysis software is the basis of a modular software system. The main RFEM 6 program is used to define structures, materials, and loads of planar and spatial structural systems consisting of plates, walls, shells, and members. The program also allows you to create combined structures as well as to model solid and contact elements.

Price of First License
3,990.00 USD
RFEM 6
Steel Design

Design

The Steel Design add-on designs steel members for the ultimate and serviceability limit states according to various standards.

Price of First License
2,200.00 USD