905 Results
View Results:
Sort by:
Stability Analysis of Structural Components with Asymmetric Cross-Section
Is it possible to use the general method according to EN 1993‑1‑1, 6.3.4 to design structural components with an asymmetric cross-section in the Steel Design add-on for RFEM 6 or RSTAB 9?
Add-ons for Timber Structures
Which Dlubal software products do you recommend for the structural analysis and design of timber structures in particular?
Comparative Analysis for RANS, URANS, and DDES Turbulence Models
What is the difference between the RANS, URANS, and DDES turbulence models?
Stability Analysis with Torsion
When performing steel design in RFEM 6 or RSTAB 9, I get a warning that the torsion is neglected in the stability design checks. What is the reason for this, and how can I get around the warning message?
Load Extension Isotropic Masonry | Plastic
Is it possible to influence the transverse distribution of a load in the case of the Isotropic | Masonry | Plastic material model?
Option – Independent FE Mesh Preferred
What is the effect of the "Independent FE Mesh Preferred" option in the mesh settings?
Importing Surfaces from Rhino into RFEM 6
Why are not all surfaces transferred when importing surfaces from Rhino into RFEM 6?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Performance Problems on Modern Intel Processors
RFEM calculates more slowly on my new computer than on the old one. What might be the cause, and how can I change it?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
Load Transfer Surfaces
The loads from the load transfer surfaces are not displayed. Where are they?
Design Cases
Can I use design cases in RFEM 6 in the same way as in RFEM 5?
Imperfection Case
There is no "Imperfection" action category. How can I create an imperfection load case?
RWIND Calculation Error E315
When performing high-quality transient simulations with a high number of mesh cells, I get this error: "Calculation failed! RWindSolverTransient failed, E315." After that, RWIND stops without results. What can I do?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Power Plants and Conveyor Structures
Which programs can I use to design power plants and conveyor structures?
Scaffolding and Rack Structures
We are looking for a program for scaffolding and rack structures. Is Dlubal Software suitable for this?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Programs for Laminate and CLT Structures
Which programs do I need for laminate and sandwich structures, or cross-laminated timber (CLT)?
Programs for Timber Structures
Which Dlubal Software programs can I use to calculate and design timber structures?
Design of Hydraulic Steel Structures
Can I analyze and design hydraulic steel structures with the Dlubal programs?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263