1108 Results
View Results:
Sort by:
FE Mesh Refinement Factor for Reducing Calculation Time
How can I reduce the calculation time for members with a nonlinear material model in RFEM 6 and RSTAB 9?
Meaning of location_flags of Class members_internal_forces (WebService API)
What is the meaning of the location_flags in the members_internal_forces class of the WebService API?
Different Stresses in Static Analysis and Stress-Strain Analysis
Why are the stresses of the structural analysis different from those calculated with the Stress-Strain Analysis add-on?
Stability Analysis of Structural Components with Asymmetric Cross-Section
Is it possible to use the general method according to EN 1993‑1‑1, 6.3.4 to design structural components with an asymmetric cross-section in the Steel Design add-on for RFEM 6 or RSTAB 9?
Structure Below Ground Level
Why does the integration/support of my building in the ground below the ground level not work?
Adjusting NDS and CSA O86 Factors for Consideration in the Timber Design Add-on
How can the NDS and CSA O86 factors be manually adjusted for consideration in the Timber Design add-on?
NDS Strength Configuration - Calculation of Torsion Settings
What calculation is carried out for the NDS Strength Configuration "Calculation of Torsion" options?
Add-ons for Timber Structures
Which Dlubal software products do you recommend for the structural analysis and design of timber structures in particular?
Comparative Analysis for RANS, URANS, and DDES Turbulence Models
What is the difference between the RANS, URANS, and DDES turbulence models?
Stability Analysis with Torsion
When performing steel design in RFEM 6 or RSTAB 9, I get a warning that the torsion is neglected in the stability design checks. What is the reason for this, and how can I get around the warning message?
Add-on Harmonic Response Analysis
I cannot activate the Harmonic Response Analysis add-on. Why?
Double-Sided Stiffening (Splice)
How can I model a timber beam with stiffening on both sides? (splice)
Load Extension Isotropic Masonry | Plastic
Is it possible to influence the transverse distribution of a load in the case of the Isotropic | Masonry | Plastic material model?
Option – Independent FE Mesh Preferred
What is the effect of the "Independent FE Mesh Preferred" option in the mesh settings?
Plastic Hinges
How do I define a plastic hinge in RFEM 6?
Add-ons for Concrete Structures
Which products do you recommend for the structural analysis and design of reinforced concrete structures?
Add-ons for Steel Structures
I process steel structures. Which products do you recommend for this area?
Direct vs. Iterative Solver
The calculation in RFEM 6 takes a very long time, but the processor utilization of my system is low. Why is this?
Not Valid/Deactivated Punching Nodes
In the table of the objects to be designed in the Concrete Design add-on, punching nodes are listed in the not valid/deactivated column, although I have defined them as punching nodes. How can I fix this?
Area Loads on Members via Cells
How can I generate an area load on members via cells in RFEM 6 or RSTAB 9?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
Graphic Templates for Printing Reinforcement Layout
How can I use graphic templates for multi printing of a reinforcement?
Design Cases
Can I use design cases in RFEM 6 in the same way as in RFEM 5?
How can I define temporary supports for a form-finding process in RFEM& 6?
How can I define temporary supports for a form-finding process in RFEM& 6?
Steady-State or Transient Simulation for Parapet in RWIND
What is the most accurate CFD method for the wind simulation of parapets?
Effective Section
Can I calculate the effective section properties of a cross-section using RSECTION?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM