The goal of structural engineering is to determine the required load-bearing capacity and serviceability of a building structure while bringing the intended service life into conformity with the economic and aesthetic requirements. To implement this task, the structural analysis applies, which is based on the rules of structural engineering. In exceptional cases, the tests serve as proof of feasibility.
Structural Analysis Wiki
The Dlubal Structural Analysis Wiki explains technical terms used in structural analysis and design. The terms are given in alphabetical order and are usually used in Dlubal Software.
- c/t-Part
- Calculation Diagram
- Cell
- Cement
- Chemical Shrinkage
- Climatic Load
- Clipping Box
- Clipping Plane
- Combination Expression
- Combination Scheme
- Combination Wizard
- Comment
- Composition
- Concrete
- Configuration Manager
- Construction Stages
- Contact Solid
- Control Panel
- Coordinate Systems
- Creep
- Cross-Section Library
- Mass Case
- Mass Combination
- Mass Loads
- Material Library
- Member
- Member Division
- Member Eccentricities
- Member Elastic Foundation
- Member Hinge
- Member Imperfection
- Member Load
- Member Loads from Area Load
- Member Loads from Free Line Load
- Member Nonlinearity
- Member Orientation
- Member Representative
- Member Result Intermediate Point
- Member Set Imperfections
- Member Set Load
- Member Set Representative
- Member Stiffness
- Member Stiffness Modification
- Member Support
- Member Type
- Minimum Reinforcement
- Modal Analysis
- Modal Mass
- Mode Shape
- Model Check
- Model Generator
- Modeling Tools
- Modulus of Elasticity
- Modulus of Elasticity
- Moving Load
- Second Moment of Area
- Second-Order Analysis
- Sections
- Selection
- Selection Options
- Service Phases
- Set of Members
- Shear Modulus
- Shear Panel
- Shear Reinforcement
- Shell
- Shrinkage
- Snow Load Wizard
- Solid
- Solid Load
- Solid Mesh Refinement
- Solid Set
- Solid Set Load
- Spring
- Static Analysis Settings
- Stiffening
- Stiffness
- Strength
- Stress
- Structural Engineering
- Structural System | Model
- Structure Modification
- Structure Stability
- Super Combination
- Support Reaction
- Surface
- Surface Contact
- Surface Contact Type
- Surface Eccentricity
- Surface Imperfections
- Surface Load
- Surface Mesh Refinement
- Surface Release
- Surface Results Adjustment
- Surface Set
- Surface Set Imperfections
- Surface Side
- Surface Stiffness
- Surface Stiffness Modification
- Surface Support
- Swelling
S
Structural Engineering
Recommended Products for You
RFEM 6 | Main Program RFEM 6
Main Program
The new generation of 3D FEA software is used for the structural analysis of members, surfaces, and solids.
Price of First License
4,170.00 USD
RFEM 6 | Additional Analysis
Add-On
The Nonlinear Material Behavior add-on allows you to consider material nonlinearities in RFEM for example, isotropic plastic, orthotropic plastic, isotropic damage).
Price of First License
1,480.00 USD
RFEM 6 | Additional Analysis
Add-On
The Structure Stability add-on performs stability analysis of structures. It determines critical load factors and the corresponding stability modes.
Price of First License
1,300.00 USD
RFEM 6 | Additional Analysis
Add-On
The Torsional Warping (7 DOF) add-on allows you to consider cross-section warping as an additional degree of freedom.
Price of First License
1,480.00 USD
RFEM 6 | Special Solutions
Add-On
The Multilayer Surfaces add-on allows you to define multilayer surface structures. The calculation can be carried out with or without the shear coupling.
Price of First License
1,300.00 USD
RFEM 6 | Special Solutions
Add-On
The two-part Optimization & Costs / CO2 Emission Estimation add-on finds suitable parameters for parameterized models and blocks via the artificial intelligence (AI) technique of particle swarm optimization (PSO) for compliance with common optimization criteria. Furthermore, this add-on estimates the model costs or CO2 emissions by specifying unit costs or emissions per material definition for the structural model.
Price of First License
1,480.00 USD
RFEM 6 | Design
Add-On
The Stress-Strain Analysis add-on performs general stress analysis by calculating the existing stresses and comparing them with the limit stresses.
Price of First License
1,210.00 USD
RFEM 6 | Design
Add-On
The Concrete Design add-on allows for various design checks according to international standards. You can design members, surfaces, and columns, as well as perform punching and deformation analyses.
Price of First License
2,550.00 USD
RFEM 6 | Design
Add-On
The Steel Design add-on performs the ultimate and serviceability limit state design checks of steel members according to various standards.
Price of First License
2,550.00 USD
RFEM 6 | Design
Add-On
The Timber Design add-on performs the ultimate, serviceability, and fire resistance limit state design checks of timber members according to various standards.
Price of First License
1,930.00 USD
RFEM 6 | Design
Add-On
The Masonry Design add-on for RFEM allows you to design masonry using the finite element method. It was developed as part of the research project titled DDMaS – Digitizing the Design of Masonry Structures. The material model represents the nonlinear behavior of the brick-mortar combination in the form of macro-modeling.
Price of First License
1,660.00 USD
RFEM 6 | Design
Add-On
The Aluminum Design add-on performs the ultimate and serviceability limit state design checks of aluminum members according to various standards.
Price of First License
1,750.00 USD
RFEM 6 | Joints
.png?mw=600&hash=49b6a289915d28aa461360f7308b092631b1446e)
Add-On
The Steel Joints add-on for RFEM allows you to analyze steel connections using an FE model. The FE model is generated automatically in the background and can be controlled via the simple and familiar input of components.
Price of First License
2,110.00 USD
RSTAB 9 | Main Program RSTAB 9
Main Program
The modern 3D structural analysis and design program is suitable for the structural and dynamic analysis of beam structures as well as the design of concrete, steel, timber, and other materials.
Price of First License
2,910.00 USD
RSTAB 9 | Additional Analysis
Add-On
The Structure Stability add-on performs the stability analysis of structures. It determines critical load factors and the corresponding stability modes.
Price of First License
1,300.00 USD
RSTAB 9 | Additional Analysis
Add-On
The Torsional Warping (7 DOF) add-on allows for considering cross-section warping as an additional degree of freedom when calculating members.
Price of First License
1,480.00 USD
RSTAB 9 | Special Solutions
Add-On
The two-part Optimization & Costs / CO2 Emission Estimation add-on finds suitable parameters for parameterized models and blocks via the artificial intelligence (AI) technique of particle swarm optimization (PSO) for compliance with common optimization criteria. Furthermore, this add-on estimates the model costs or CO2 emissions by specifying unit costs or emissions per material definition for the structural model.
Price of First License
1,480.00 USD
RSTAB 9 | Design
Add-On
The Stress-Strain Analysis add-on performs a general stress analysis by calculating the existing stresses and comparing them to the limit stresses.
Price of First License
1,120.00 USD
RSTAB 9 | Design
Add-On
Concrete Design add-on allows for various design checks of members and columns according to international standards.
Price of First License
2,550.00 USD
RSTAB 9 | Design
Add-On
The Steel Design add-on performs the ultimate and serviceability limit state design checks of steel members according to various standards.
Price of First License
2,550.00 USD
RSTAB 9 | Design
Add-On
The Timber Design add-on performs the ultimate, serviceability, and fire resistance limit state design checks of timber members according to various standards.
Price of First License
1,930.00 USD
RSTAB 9 | Design
Add-On
The Aluminum Design add-on performs the ultimate and serviceability limit state design checks of aluminum members according to various standards.
Price of First License
1,750.00 USD