Зарегистрируйтесь в экстранете Dlubal, чтобы оптимизировать использование вашего программного обеспечения и получить эксклюзивный доступ к вашим личным данным.
Труба с трубчатым сечением загружена внутренним давлением. This internal pressure causes axial deformation of the pipe (the Bourdon effect). Determine the axial deformation of the pipe endpoint.
На консоль из круглого стержня действует внецентренная поперечная сила. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
На консоль из круглого стержня действует внецентренная равномерная нагрузка. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
Консоль из круглого стержня нагружена внецентренной нормальной силой. Determine the maximum vertical deflection of the console using the geometrically linear and second-order analysis.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Собственный вес не учитывается. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Балка, шарнирно опертая на обоих концах, загружена сосредоточенной силой в середине. Neglecting its self-weight and shear stiffness, determine the beam's maximum deflection, normal force, and moment at the mid-span, assuming the second- and third-order analysis.
Цель данного примера - продемонстрировать необратимые процессы, вызванные трением. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.
Между двумя опорами подвешены очень жесткие канаты. Determine the equilibrium shape of the cable (the catenary), consider the gravitational acceleration, and neglect the stiffness of the cable. Verify the position of the cable at the given test points.
Компактный диск (CD) вращается со скоростью 10 000 об/мин. Therefore, it is subjected to centrifugal force. The problem is modeled as a quarter model. Determine the tangential stress on the inner and outer diameters and the radial deflection of the outer radius.
Стальная балка квадратного сечения нагружена нормальной силой и распределенной нагрузкой. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Стальная балка квадратного сечения с осевой нагрузкой имеет шарнирное закрепление на одном конце и подпружинивание - на другом. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
Рассмотрим жесткую трубу строительных лесов, закрепленную снизу с помощью Узловой опоры лесов и нагруженную моментом и силой. Calculate the maximum deflection with consideration of initial slippage.
Рассмотрим жесткую трубу строительных лесов, закрепленную снизу с помощью Узловой опоры лесов и нагруженную моментом и силой. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Рассмотрим жесткую трубу строительных лесов, закрепленную снизу с помощью Узловой опоры лесов и нагруженную моментом и силой. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Конструкция состоит из четырех ферм, встроенных в шарнирные опоры. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Многослойная консоль состоит из трех слоев (сердечника и двух сторон). Она закреплена на левом конце и загружена сосредоточенной силой на правом конце.
В тонкостенный сферический резервуар действует внутреннее давление. While neglecting self‑weight, determine the von Mises stress and the radial deflection of the vessel.
Конический тонкостенный резервуар заполнен водой. Thus, it is loaded by hydrostatic pressure. While neglecting self-weight, determine the stresses in the surface line and circumferential direction. The analytical solution is based on the theory of thin-walled vessels. This theory was introduced in Verification Example 0084.
Тонкая прямоугольная ортотропная пластина оперта просто, и она загружена равномерно распределенным давлением. The directions of axes x and y coincide with the principal directions. While neglecting self-weight, determine the maximum deflection of the plate.
Открытый резервуар с толстыми стенками загружен внутренним и внешним давлением (поэтому в нем нет нормального напряжения). While neglecting self-weight, the radial deflection of the inner and the outer radius is determined.
Стальной стержень между двумя жесткими опорами с зазором нагружен перепадом температур. While neglecting self‑weight, determine the total deformation of the rod and its internal axial force.
Кирпичная стена подвержена распределенной нагрузке в середине своего верхнего сечения. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Определите максимальный прогиб и напряжение в направлении z для составной пластины, состоящей из двух слоев стекла и одного промежуточного слоя фольги, подверженной равномерному давлению.
Композитная плита, состоящая из трех слоев стекла, одного слоя фольги и внутреннего пространства с осушенным воздухом, полностью закреплена и нагружена переменной температурой. Neglecting its self-weight, determine the plate's maximum deflection.
Одна многослойная квадратная ортотропная плита полностью закреплена в своей средней точке и подвергается давлению. Compare the deflections of the plate corners to check the correctness of the transformation.
Рассмотрим соединение труб строительных лесов, подверженное действию осевой силы и момента. Self-weight is not considered. The material of the tube is idealized as perfectly rigid. All geometrical non-linearities are ignored. Determine the angle of deflection.