Determine a resistência à compressão normal admissível de uma viga articulada de 2,44 m de comprimento com diferentes secções feitas de liga 6061-T6, que se encontra encastrada lateralmente para evitar a encurvadura em torno do eixo fraco de acordo com o Aluminium Design Manual (ADM).
Determine a resistência à compressão normal admissível de uma viga articulada de 2,44 m de comprimento com diferentes secções feitas de liga 6061-T6, que se encontra encastrada lateralmente para evitar a encurvadura em torno do eixo fraco de acordo com o Aluminium Design Manual (ADM).
A strut with a circular cross-section is supported according to four basic cases of Euler buckling and subjected to pressure force. Determine a carga de encurvadura crítica.
Determine a resistência à compressão normal admissível de uma viga articulada de 2,44 m de comprimento com diferentes secções feitas de liga 6061-T6, que se encontra encastrada lateralmente para evitar a encurvadura em torno do eixo fraco de acordo com o Aluminium Design Manual (ADM).
A column is composed of a concrete section (rectangle 100/200) and a steel section (profile I 200). Está sujeito a uma força de compressão. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
Um quarto de barra circular com uma secção retangular é carregado com uma força fora do plano. This force causes a bending moment, torsional moment, and transverse force. While neglecting self-weight, determine the total deflection of the curved beam.
Um sistema de duas massas é constituído por dois eixos e duas massas que são representados pelos momentos de inércia correspondentes e estão concentrados a uma dada distância como massas nodais. The left shaft is fixed, and the right mass is free. Neglecting the self‑weight of the shafts, determine the torsional natural frequencies of the system.
A placa triangular equilateral simplesmente apoiada é carregada com uma carga transversal distribuída uniformemente. Assuming the small deformation theory and neglecting self‑weight, the maximum out‑of‑plane deflection of the plate is determined.
A placa retangular Kirchhoff apoiada de forma simples está sujeita a compressão lateral uniforme e é alongada por uma carga distribuída. The maximum out-of-plane deflection is determined by assuming small deformations.
Este exemplo serve para ilustrar o plano. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
A member with the given boundary conditions is loaded by torsional moment and axial force. Neglecting its self-weight, determine the beam's maximum torsional deformation as well as its inner torsional moment, defined as the sum of a primary torsional moment and torsional moment caused by the normal force. Compare estes valores ao mesmo tempo que aceita ou não considera a influência da força axial. The verification example is based on the example introduced by Gensichen and Lumpe.
A viga está completamente fixada na extremidade esquerda (empenamento restringido) e apoiada na extremidade direita por um apoio de forquilha (empenamento possibilitado). The beam is subjected to a torque, longitudinal force, and transverse force. Determine the behavior of the primary torsional moment, secondary torsional moment, and warping moment. The verification example is based on the example introduced by Gensichen and Lumpe.
A viga em consola com um perfil em I está apoiada na extremidade esquerda e é carregada com um binário. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).