Мембрана растягивается посредством изотропного преднапряжения между двумя радиусами двух концентрических цилиндров, не лежащих в плоскости, параллельной вертикальной оси. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Consider an ASTM A992 W 18×50 beam forspan and uniform dead and live loads as shown in Figure 1. Стержень ограничен максимальной номинальной высотой 18 дюймов (45,72 см). The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Криволинейная балка состоит из двух балок с прямоугольным сечением. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
Простой осциллятор состоит из массы m (рассчитываемой только в направлении x) и линейной пружины с жесткостью k. The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
Кирпичная стена подвержена распределенной нагрузке в середине своего верхнего сечения. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
A structure is made of two trusses of unequal length, which are embedded into the hinge supports. The structure is loaded by concentrated force. Собственный вес не учитывается. Determine the relationship between the loading force and the deflection, considering large deformations.
Рассмотрим жесткую трубу строительных лесов, закрепленную снизу с помощью Узловой опоры лесов и нагруженную моментом и силой. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
В длинной тонкой балке, несущей сосредоточенную массу, она нагружена зависящей от времени силой. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
Деревянная балка, усиленная на концах двумя стальными пластинами, подвергается нагрузке давления. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
A structure is made of two trusses, which are embedded into the hinge supports. The structure is loaded by concentrated force. Собственный вес не учитывается. Determine the relationship between the loading force and the deflection, considering large deformations.
Конструкция из двутавровых ферм опирается на обоих концах пружинные скользящие опоры и нагружена поперечными силами. The self-weight is neglected in this example. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
На левом конце поддерживается двутавровая консоль, которая нагружена крутящим моментом. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).
На обоих концах затем закреплен трехмерный блок из упруго-пластического материала. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Теперь можно определить максимальный прогиб трехмерного блока, защемленного на обоих концах. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. The block's middle plane is subjected to vertical pressure.
Деревянная балка, усиленная на концах двумя стальными пластинами, подвергается нагрузке давления. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
На обоих концах закреплен трехмерный блок из упруго-пластического материала с упрочнением. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.