Мы определим постоянную кручения для сечения трубки (кольцевая площадь) аналитически и сравним полученные результаты с численным решением в RFEM 5 и RSTAB 8 для различной толщины стенки.
Консоль прямоугольного сечения лежит на упругом Винклеровом основании и загружена распределенной нагрузкой. The image shows the calculation of the maximum deflection and maximum bending moment.
Стальная балка квадратного сечения нагружена нормальной силой и распределенной нагрузкой. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Стальная балка квадратного сечения с осевой нагрузкой имеет шарнирное закрепление на одном конце и подпружинивание - на другом. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
Одна многослойная квадратная ортотропная плита полностью закреплена в своей средней точке и подвергается давлению. Compare the deflections of the plate corners to check the correctness of the transformation.
Консоль с волокнами, идущими не в направлении оси балки от квадратного сечения с растягивающим давлением. Calculate the maximum deflection.
На обоих концах затем закреплен трехмерный блок из упруго-пластического материала. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Теперь можно определить максимальный прогиб трехмерного блока, защемленного на обоих концах. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. The block's middle plane is subjected to vertical pressure.
Определите максимальный прогиб четырех колонн, закрепленных снизу и соединенных жестким блоком сверху. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
Деревянная балка, усиленная на концах двумя стальными пластинами, подвергается нагрузке давления. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
На обоих концах закреплен трехмерный блок из упруго-пластического материала с упрочнением. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
Определение максимального прогиба куба. The cube's lower side is fully fixed and the upper side is subjected to shear loading.
Консоль полностью защемлена на левом конце и загружена поперечной и осевой силой на правом конце. The tensile strength is zero and the behavior in the compression remains elastic.
Определение максимальных прогибов блока с учетом или без учета действия сдвига. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Определите максимальный прогиб и напряжение в направлении z для составной пластины, состоящей из двух слоев стекла и одного промежуточного слоя фольги, подверженной равномерному давлению.
Широкая пластина с отверстием загружена в одном направлении растягивающим напряжением. The plate width is large with respect to the hole radius, and it is very thin, considering the state of the plane stress.
Докажите, что соединение различных размерных элементов не влияет на результаты. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
Деревянная балка, усиленная на концах двумя стальными пластинами, подвергается нагрузке давления. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Четыре колонны закреплены снизу и соединены жестким блоком наверху. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Коническая консоль полностью закреплена на левом конце и нагружена непрерывной нагрузкой. Plastic material is considered for the calculation.