Контрольный пример описывает ветровые нагрузки в нескольких направлениях ветра на модели группы зданий. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Контрольный пример описывает сжимающие нагрузки на стены зданий в тандемном расположении, расположенных на уровне земли. The buildings are simplified to rectangular objects and scaled down while maintaining the elevation ratios. The pressure distribution on the walls of the model of a medium-high building was conducted by an experiment. The chosen results (pressure coefficient Cp) are compared with the measured values.
Контрольный пример описывает стационарный поток вокруг высотного здания в городской застройке (масштабная модель). The example is given by the Architectural Institute of Japan (AIJ). The chosen results (velocity magnitude) are compared with the measured values.
Контрольный пример описывает стационарный поток вокруг отдельностоящего здания (масштабированная модель).Пример был предоставлен Архитектурным институтом Японии (AIJ). The chosen results (velocity magnitude) are compared with the measured values.
A sphere is subjected to a uniform flow of viscous fluid. The velocity of the fluid is considered at infinity. The goal is to determine the drag force. The parameters of the problem are set so that the Reynolds number is small and the radius of the sphere is also small, thus the theoretical solution can be reached - Stokes flow (G. G. Stokes 1851).
Толстостенный резервуар нагружен внутренним давлением так, что он достигает упруго-пластического состояния. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
Кирпичная стена подвержена распределенной нагрузке в середине своего верхнего сечения. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Консоль загружена поперечной и осевой силой на правом конце и полностью защемлена на левом конце. The problem is described by the following set of parameters. The problem is solved by using the geometrically linear analysis, second-order analysis, and large deformation analysis.
В длинной тонкой балке, несущей сосредоточенную массу, она нагружена зависящей от времени силой. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
Расчет изменений во времени для консольной балки (система SDOF), возбужденной периодической функцией. Vertical deformations and accelerations calculated with direct integration and modal analysis in RF‑/DYNAM Pro - Forced Vibrations are compared with the analytical solution.
Деревянная балка, усиленная на концах двумя стальными пластинами, подвергается нагрузке давления. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Собственный вес не учитывается. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Определите максимальный прогиб четырех колонн, закрепленных снизу и соединенных жестким блоком сверху. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
Деревянная балка, усиленная на концах двумя стальными пластинами, подвергается нагрузке давления. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.