Контрольный пример описывает сжимающие нагрузки на стены зданий в тандемном расположении, расположенных на уровне земли. The buildings are simplified to rectangular objects and scaled down while maintaining the elevation ratios. The pressure distribution on the walls of the model of a medium-high building was conducted by an experiment. The chosen results (pressure coefficient Cp) are compared with the measured values.
Сферическая мембрана воздушного потока заполнена газом под заданным атмосферным давлением и заданным объемом (эти значения используются только для задания модели КЭ). Determine the overpressure inside the balloon due to the given isotropic membrane prestress. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Труба с трубчатым сечением загружена внутренним давлением. This internal pressure causes axial deformation of the pipe (the Bourdon effect). Determine the axial deformation of the pipe endpoint.
Колонна состоит из бетонного сечения (прямоугольник 100/200) и стального сечения (профиль I 200). It is subjected to pressure force. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
Этот пример является модификацией контрольного примера 0061; разница лишь в том, что материал резервуара несжимаемый. An open‑ended, thick‑walled vessel is loaded by both inner and outer pressure. While neglecting self‑weight, the radial deflection of the inner and the outer radius is determined.
Двухслойный резервуар с открытыми концами и массивными стенками загружен внутренним и внешним давлением; таким образом, нет нормального напряжения. While neglecting self‑weight, the radial deflection of the inner and outer radius, and the pressure (radial stress) in the middle radius is determined.
Четыре колонны закреплены снизу и соединены жестким блоком наверху. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Потом определите максимальный прогиб консоли, состоящей из двух слоев стекла и одного промежуточного слоя пленки. The plate is fully fixed at one end and subjected to uniform pressure.
На обоих концах затем закреплен трехмерный блок из упруго-пластического материала. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Теперь можно определить максимальный прогиб трехмерного блока, защемленного на обоих концах. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. The block's middle plane is subjected to vertical pressure.
Определите максимальный прогиб четырех колонн, закрепленных снизу и соединенных жестким блоком сверху. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
На обоих концах закреплен трехмерный блок из упруго-пластического материала с упрочнением. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
Определение максимальных прогибов блока с учетом или без учета действия сдвига. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.