A estrutura é constituída por uma viga de secção em I e duas vigas treliçadas de tubo. A estrutura contém várias imperfeições e é carregada pela força Fz. O peso próprio não é considerado neste exemplo. Determine as flechas uy e uz e a rotação axial φx no ponto final (ponto 4). O exemplo de verificação é baseado no exemplo introduzido por Gensichen e Lumpe.
Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Calculate the maximum deflection with consideration of initial slippage.
Este exemplo de verificação é baseado no exemplo de verificação 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
O exemplo de verificação descreve cargas de vento em várias direções do vento num modelo de um grupo de edifícios. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Determine a flecha e o momento radial máximos de uma placa circular de apoio simples sujeita a pressão, temperatura e temperatura diferencial constantes.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. É apoiada de forma simples. The problem is described using the following parameters. Determine the deflections in the given test times.
Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
A placa ortotrópica quadrada em camadas está completamente fixada no seu ponto central e sujeita a compressão. Compare as flechas dos cantos da placa para verificar a exatidão da transformação.
Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
A viga de aço de secção quadrada está sujeita a uma força normal e a uma carga distribuída. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Um sistema de massa singular com folga e duas molas é desviado primeiro. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
Um cabo de aço ou uma membrana com pinos nas duas extremidades é carregado por uma carga distribuída. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
Uma consola constituída por uma barra de secção circular está sujeita a uma carga uniforme excêntrica. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
A thick-walled vessel is loaded by an inner pressure such that the vessel reaches an elastic-plastic state. São determinadas e comparadas as soluções analíticas e numéricas para a posição radial da zona de fronteira plástica (de acordo com a hipótese de Tresca), não sendo considerado o peso próprio.
Uma viga ASTM A992 W 24×62 com corte nas extremidades de 24 e 72,5 t das cargas permanente e variável, respetivamente, é apresentada na Figura 01. Verify the available shear strength of the selected beam, based on LRFD and ASD.
A cantilever of rectangular cross‑section has a mass at the end. Além disso, é carregada por uma força axial. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Um sistema de massa singular com amortecimento está sujeito a uma força de carga constante. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Uma membrana é esticada através de um pré-esforço isotrópico entre dois raios de dois cilindros concêntricos que não se encontram num plano paralelo ao eixo vertical. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Considere o vão da barra ASTM A992 W 18×50 apresentado na Figura 01 e as cargas permanentes e variáveis uniformes. A barra está limitada a uma altura máxima de 45,72 cm (18 pol.). A flecha da carga variável está limitada a L/360. A viga está apoiada de forma simples e contraventada de forma contínua. Verifique a resistência à flexão disponível da viga selecionada com base nos métodos LRFD e ASD.
Determine as flechas máximas do bloco, tendo em consideração ou negligenciando o efeito de corte. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Uma consola está completamente fixada na extremidade esquerda e carregada por uma força de corte e uma força axial na extremidade direita. The tensile strength is zero and the behavior in the compression remains elastic.
Determine a flecha e a tensão máximas na direção z para um painel laminado sob pressão constante, constituído por duas camadas de vidro e uma camada intermédia de folha.
O painel laminado constituído por três camadas de vidro, uma camada de folha e um espaço interior com ar seco está completamente fixado e é carregado com uma temperatura variável. Neglecting its self-weight, determine the plate's maximum deflection.
A compact disc (CD) rotates at a speed of 10,000 rpm. Está, por isso, sujeito a uma força centrífuga. The problem is modeled as a quarter model. Determine the tangential stress on the inner and outer diameters and the radial deflection of the outer radius.
Uma barra de tração em forma de W de acordo com a ASTM A992 é selecionada para suportar sob tração uma carga permanente de 30 000 kips (13,6 t) e uma carga variável de 90 000 kips (40,8 t). Verify the member strength using both LRFD and ASD.
Determine a resistência à compressão normal admissível de uma viga articulada de 2,44 m de comprimento com diferentes secções feitas de liga 6061-T6, que se encontra encastrada lateralmente para evitar a encurvadura em torno do eixo fraco de acordo com o Aluminium Design Manual (ADM).
Determine the maximum deflection of a three-dimensional block fixed at both ends. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. O plano central do bloco está sob pressão vertical.