Das Architectural Institute of Japan (AIJ) ставит Рейхе заранее на Benchmark-Szenarien für Windsimulation vorgestellt. Der Nachfolgende Beitrag dreht sich dabei um den «Случай А - высотное здание формы 2: 1: 1». Im Folgenden wird das beschriebene Szenario в RWIND2 nachgebildet und die Ergebnisse mit den simulierten und der Experimentellen Resultate des AIJ verglichen.
Контрольный пример описывает сжимающие нагрузки на стены зданий в тандемном расположении, расположенных на уровне земли. The buildings are simplified to rectangular objects and scaled down while maintaining the elevation ratios. The pressure distribution on the walls of the model of a medium-high building was conducted by an experiment. The chosen results (pressure coefficient Cp) are compared with the measured values.
Контрольный пример описывает стационарный поток вокруг высотного здания в городской застройке (масштабная модель). The example is given by the Architectural Institute of Japan (AIJ). The chosen results (velocity magnitude) are compared with the measured values.
Контрольный пример описывает стационарный поток вокруг отдельностоящего здания (масштабированная модель).Пример был предоставлен Архитектурным институтом Японии (AIJ). The chosen results (velocity magnitude) are compared with the measured values.
Мембрана растягивается посредством изотропного преднапряжения между двумя радиусами двух концентрических цилиндров, не лежащих в плоскости, параллельной вертикальной оси. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Consider an ASTM A992 W 18×50 beam forspan and uniform dead and live loads as shown in Figure 1. Стержень ограничен максимальной номинальной высотой 18 дюймов (45,72 см). The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
На рисунке 1 показана балка ASTM A992 W 24x62 со сдвигом на концах 48 000 и 145 000 kips от постоянной и временной нагрузки соответственно. Verify the available shear strength of the selected beam, based on LRFD and ASD.
Колонна состоит из бетонного сечения (прямоугольник 100/200) и стального сечения (профиль I 200). It is subjected to pressure force. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
Балка в форме четверти окружности с прямоугольным сечением загружена силой, находящейся вне плоскости. This force causes a bending moment, torsional moment, and transverse force. While neglecting self-weight, determine the total deflection of the curved beam.
Криволинейная балка состоит из двух балок с прямоугольным сечением. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
У конструкции кровли оболочки, находящейся под нагрузкой давления, прямые края являются свободными, а на изогнутых краях перемещения y и z ограничены. Neglecting self‑weight, compute the maximum (absolute) vertical deflection, and compare the results with COMSOL Multiphysics 4.3.
Шарнирно опертая балка с прямоугольным сечением, подверженная распределенной нагрузке, смещается в вертикальном направлении за счет эксцентриситета. Considering the small deformation theory, neglecting the self‑weight, and assuming that the beam is made of isotropic elastic material, determine the maximum deflection.
В данный момент в середине пролета простой опорной балки внезапно приложена сосредоточенная сила. Considering only the small deformation theory, determine the maximum deflection of the beam.
В середине пролета простой опёртой балки в течение короткого промежутка времени приложена сосредоточенная сила. Considering only the small deformation theory and assuming that the mass of the beam is concentrated at its mid‑span, determine its maximum deflection.
Двухэтажная однопролетная каркасная конструкция подвержена сейсмической нагрузке. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
К тому же, на свободном конце консоли действует момент, Using the geometrically linear analysis and large deformation analysis, and neglecting the beam's self-weight, determine the maximum deflections at the free end. The verification example is based on the example introduced by Gensichen and Lumpe.
Стержень с заданными граничными условиями нагружен крутящим моментом и нормальной силой. Neglecting its self-weight, determine the beam's maximum torsional deformation as well as its inner torsional moment, defined as the sum of a primary torsional moment and torsional moment caused by the normal force. Provide a comparison of those values while assuming or neglecting the influence of the normal force. The verification example is based on the example introduced by Gensichen and Lumpe.
Деревянная балка, усиленная на концах двумя стальными пластинами, подвергается нагрузке давления. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Определите изгибающий момент, действующий на свободный конец консоли, который изгибает стержень до круглой формы. Neglecting the beam's self-weight, assuming the large deformation analysis, and loading the cantilever with the moment, determine its maximum deflections.
Балка полностью закреплена (депланация ограничена) на левом конце и поддерживается вилочной опорой (депланация включена) на правом конце. The beam is subjected to a torque, longitudinal force, and transverse force. Determine the behavior of the primary torsional moment, secondary torsional moment, and warping moment. The verification example is based on the example introduced by Gensichen and Lumpe.
Балка, шарнирно опертая на обоих концах, загружена сосредоточенной силой в середине. Neglecting its self-weight and shear stiffness, determine the beam's maximum deflection, normal force, and moment at the mid-span, assuming the second- and third-order analysis.
Рассмотрим жесткую трубу строительных лесов, закрепленную снизу с помощью Узловой опоры лесов и нагруженную моментом и силой. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Собственный вес не учитывается. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Стальная балка квадратного сечения с осевой нагрузкой имеет шарнирное закрепление на одном конце и подпружинивание - на другом. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
Деревянная балка, усиленная на концах двумя стальными пластинами, подвергается нагрузке давления. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.