A simply supported beam is loaded by pure bending. Devido à encurvadura por flexão, tente determinar a carga de encurvadura crítica e o fator de carga correspondente.
A strut with a circular cross-section is supported according to four basic cases of Euler buckling and subjected to pressure force. Determine a carga de encurvadura crítica.
A thin rectangular orthotropic plate is simply supported and loaded by uniformly distributed pressure. The directions of axes x and y coincide with the principal directions. Determine a flecha máxima do painel, sem considerar o peso próprio.
Um oscilador simples é composto por massa m (a ser considerada apenas na direção x-) e pela mola linear com a rigidez k. The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
A viga em consola com um perfil em I está apoiada na extremidade esquerda e é carregada com um binário. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).
Este exemplo serve para ilustrar o plano. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
Um cabo na posição inicial é carregado por duas forças concentradas. The self‑weight is neglected. Determine the normal forces in the cable.
A structure made of an I-profile is fully fixed on the left end and embedded into the sliding support on the right end. A estrutura é constituída por dois segmentos. The self-weight is neglected in this example. Determine the maximum deflection of the structure, the bending moment on the fixed end, the rotation of segment 2, and the reaction force at point B by means of the geometrically linear analysis and the second-order analysis. The verification example is based on the example introduced by Gensichen and Lumpe.
A structure made of I-profile trusses is supported on both ends by spring sliding supports and loaded by transversal forces. O peso próprio não é considerado neste exemplo. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
A estrutura de pórticos de dois pisos está sujeita a cargas sísmicas. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
Uma treliça plana constituída por quatro barras inclinadas e uma barra vertical é carregada no nó superior através de uma força vertical e uma força fora do plano. Assuming the large deformation analysis and neglecting the self-weight, determine the normal forces of the members and the out-of-plane displacement of the upper node.
Considere o vão da barra ASTM A992 W 18×50 apresentado na Figura 01 e as cargas permanentes e variáveis uniformes. The member is limited to a maximum nominal depth of 18 inches. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Nos apoios da forquilha está integrada uma estrutura constituída por um perfil em I. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
Verifique se os resultados não são afetados pelo acoplamento de diferentes elementos dimensionais. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
Um sistema de massa singular com amortecimento está sujeito a uma força de carga constante. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Imaginemos um tubo de andaime resistente à flexão fixado por um apoio nodal para andaimes na parte inferior e carregado por um momento e por uma força. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.