Конструкция состоит из двутавровой балки и двух трубчатых ферм. The structure contains several imperfections and it is loaded by the force Fz. В данном примере не учитывается собственный вес. Determine the deflections uy and uz and axial rotation φx at the endpoint (Point 4). Данный контрольный пример основан на примере, представленном Gensichen и Lumpe.
Данный контрольный пример основан на контрольном примере 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Рассмотрим жесткую трубу строительных лесов, закрепленную снизу с помощью Узловой опоры лесов и нагруженную моментом и силой. Calculate the maximum deflection with consideration of initial slippage.
Контрольный пример описывает ветровые нагрузки в нескольких направлениях ветра на модели группы зданий. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Определение максимального прогиба и максимального радиального момента у круглой пластины, опертой просто, на которую действует равномерное давление, равномерная температура и перепад температур.
В длинной тонкой балке, несущей сосредоточенную массу, она нагружена зависящей от времени силой. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
Рассмотрим жесткую трубу строительных лесов, закрепленную снизу с помощью Узловой опоры лесов и нагруженную моментом и силой. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Одна многослойная квадратная ортотропная плита полностью закреплена в своей средней точке и подвергается давлению. Сравните прогибы углов пластины, чтобы проверить правильность преобразования.
Рассмотрим жесткую трубу строительных лесов, закрепленную снизу с помощью Узловой опоры лесов и нагруженную моментом и силой. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Стальная балка квадратного сечения нагружена нормальной силой и распределенной нагрузкой. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
- 000119
- Расчет
- RFEM 5
-
- RSTAB 8
- RF-DYNAM Pro | Natural Vibrations 5
- RF-DYNAM Pro | Forced Vibrations 5
- RF-DYNAM Pro | Equivalent Loads 5
- RF-DYNAM Pro | Nonlinear Time History 5 (нелинейное изменение во времени)
- DYNAM Pro | Natural Vibrations 8 (собственные колебания)
- DYNAM Pro | Equivalent Loads (Эквивалентные нагрузки) 8
- DYNAM Pro | Nonlinear Time History 8
Сначала прогибается система с одной массой, с допуском и двумя пружинами. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
На консоль из круглого стержня действует внецентренная равномерная нагрузка. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
Стальной канат или мембрана со штифтами на обоих концах нагружены распределенной нагрузкой. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
Толстостенный резервуар нагружен внутренним давлением так, что он достигает упруго-пластического состояния. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
На систему единичных масс действует сила нагрузки. Determine the deflection of the system.
На рисунке 1 показана балка ASTM A992 W 24x62 со сдвигом на концах 48 000 и 145 000 kips от постоянной и временной нагрузки соответственно. Verify the available shear strength of the selected beam, based on LRFD and ASD.
У консоли с прямоугольным сечением на конце имеется масса. Furthermore, it is loaded by an axial force. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Определение максимального прогиба куба. The cube's lower side is fully fixed and the upper side is subjected to shear loading.
Определение максимальных прогибов блока с учетом или без учета действия сдвига. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
- 000121
- Расчет
- RFEM 5
-
- RSTAB 8
- RF-DYNAM Pro | Natural Vibrations 5
- RF-DYNAM Pro | Forced Vibrations 5
- RF-DYNAM Pro | Equivalent Loads 5
- RF-DYNAM Pro | Nonlinear Time History 5 (нелинейное изменение во времени)
- DYNAM Pro | Natural Vibrations 8 (собственные колебания)
- DYNAM Pro | Equivalent Loads (Эквивалентные нагрузки) 8
- DYNAM Pro | Nonlinear Time History 8
Система единичных масс с амортизатором находится под действием постоянной нагруженной силы. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.