El Instituto de Arquitectura de Japón (AIJ) ha eine Reihe an bekannten Benchmark-Szenarien für Windsimulation vorgestellt. Der Nachfolgende Beitrag dreht sich dabei um den "Caso A - Edificio de gran altura con una forma 2: 1: 1". Im Folgenden wird das beschriebene Szenario in RWIND2 nachgebildet und die Ergebnisse mit den simulierten und der experimentantellen Resultate des AIJ verglichen.
El ejemplo de verificación describe las cargas de viento en varias direcciones del viento en un modelo de un grupo de edificios. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Este ejemplo de verificación compara los cálculos de la carga de viento en un edificio con cubierta a dos aguas utilizando la norma ASCE 7-16 y utilizando la simulación CFD en RWIND Simulation. The building is defined according to the sketch and the inflow velocity profile taken from the ASCE 7-16 standard.
Este ejemplo de verificación compara los cálculos de la carga de viento en un edificio de cubierta plana utilizando la norma ASCE 7-16 y utilizando la simulación CFD en RWIND Simulation. The building is defined according to the sketch and the inflow velocity profile taken from the ASCE 7-16 standard.
El ejemplo de verificación compara el cálculo de la carga de viento en un edificio con una cubierta a dos aguas utilizando la norma EN 1991-1-4 y utilizando la simulación CFD en RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.
El ejemplo de verificación compara el cálculo de la carga de viento en un edificio con una cubierta plana utilizando la norma EN 1991-1-4 y utilizando la simulación CFD en RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.
Un sistema de una sola masa con juego y dos muelles se deforma inicialmente. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
Una estructura superficial simétrica se compone de ocho barras de celosía iguales, que están incrustadas en los apoyos de las articulaciones. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
Una membrana de globo esférico se llena con gas con presión atmosférica y volumen definido (estos valores se usan solo para la definición del modelo de elementos finitos). Determine the overpressure inside the balloon due to the given isotropic membrane prestress. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Una estructura se compone de cuatro barras de celosía, que están incrustadas en apoyos de articulación. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Un oscilador simple consta de una masa m (considerada solo en la dirección x) y un muelle lineal de rigidez k. The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
Una fuerza concentrada se aplica repentinamente en la mitad del vano de una viga simplemente apoyada en un momento dado. Considering only the small deformation theory, determine the maximum deflection of the beam.
Una estructura de pórtico de un solo vano de dos plantas está sometida a una carga sísmica. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
Un voladizo de una sección rectangular se encuentra sobre una cimentación elástica de Pasternak y se carga mediante una carga distribuida. The image shows the calculation of the maximum deflection and maximum bending moment.
Un muro de fábrica está expuesto a una carga distribuida en el medio de su sección superior. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
A structure is made of two trusses of unequal length, which are embedded into the hinge supports. The structure is loaded by concentrated force. Se omite el peso propio. Determine the relationship between the loading force and the deflection, considering large deformations.
Un voladizo de sección variable está completamente fijado en el extremo izquierdo y cargado por una carga continua. Plastic material is considered for the calculation.
A structure is made of two trusses, which are embedded into the hinge supports. The structure is loaded by concentrated force. Se omite el peso propio. Determine the relationship between the loading force and the deflection, considering large deformations.
Un voladizo de una sección rectangular se encuentra sobre un apoyo elástico de Winkler y se carga mediante una carga distribuida. The image shows the calculation of the maximum deflection and maximum bending moment.
Una viga de acero con una sección cuadrada está cargada con un esfuerzo axil y una carga distribuida. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Una viga de acero cargada axialmente con una sección cuadrada está articulada en un extremo y apoyada en un muelle en el otro. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.