Uma combinação de pontos com a geometria cortada dos lados da base de dados do RFEM 6 e da superfície de corte. Dabei werden insgesamt 3 Últimosistema.
Este exemplo compara os comprimentos efetivos e o fator de carga crítica, que podem ser calculados no RFEM 6 utilizando o módulo Estabilidade da estrutura, com um cálculo manual. A estrutura é um pórtico encastrado com dois pilares biarticulados adicionais. Este pilar está sujeito a cargas concentradas verticais.
Neste exemplo, o corte na interface entre betão moldado em momentos diferentes e a armadura correspondente é determinado de acordo com a norma DIN EN 1992-1-1. Os resultados obtidos com o RFEM 6 serão comparados com o cálculo manual abaixo.
Os recalques de uma fundação rígida quadrada sobre uma argila lacustre [1] são calculados com o RFEM. Um quarto da fundação é modelado. A fundação tem uma largura de 75,0 m em ambos os lados. As fases de construção são utilizadas para gerar os resultados.
Determine a resistência à compressão normal admissível de uma viga articulada de 2,44 m de comprimento com diferentes secções feitas de liga 6061-T6, que se encontra encastrada lateralmente para evitar a encurvadura em torno do eixo fraco de acordo com o Aluminium Design Manual (ADM).
O exemplo de verificação descreve as cargas de pressão nas paredes do edifício em disposição tandem ao nível do solo. The buildings are simplified to rectangular objects and scaled down while maintaining the elevation ratios. The pressure distribution on the walls of the model of a medium-high building was conducted by an experiment. The chosen results (pressure coefficient Cp) are compared with the measured values.
This verification example compares wind load calculations on a duopitch roof building using the ASCE 7-16 standard and using CFD simulation in RWIND Simulation. O edifício é definido conforme o esboço e o perfil da velocidade do fluxo contido na norma ASCE 7-16.
This verification example compares wind load calculations on a flat roof building using the ASCE 7-16 standard and using CFD simulation in RWIND Simulation. O edifício é definido conforme o esboço e o perfil da velocidade do fluxo contido na norma ASCE 7-16.
No exemplo de verificação, o cálculo de cargas de vento num edifício com cobertura de duas águas utilizando a norma EN 1991-1-4 é comparado com uma simulação CFD no RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.
No exemplo de verificação, o cálculo da carga de vento num edifício com cobertura plana utilizando a norma EN 1991-1-4 é comparado com uma simulação CFD no RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.
Uma estrutura plana simétrica é constituída por oito treliças idênticas encastradas em apoios articulados. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
Uma estrutura é constituída por quatro treliças encastradas em apoios articulados. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
A compact disc (CD) rotates at a speed of 10,000 rpm. Está, por isso, sujeito a uma força centrífuga. The problem is modeled as a quarter model. Determine the tangential stress on the inner and outer diameters and the radial deflection of the outer radius.
É definida uma viga em consola com uma secção de viga em I de comprimento L. The beam has five mass points with masses m acting in the X-direction. The self-weight is neglected. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Determine analiticamente o momento de inércia de torção para a secção do tubo (superfície em anel) e compare os resultados para diferentes espessuras de parede com a solução numérica no RFEM 5 e no RSTAB 8.