该验算示例是基于验算示例 0122 编写的. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
验算示例描述了作用在建筑物模型上多个风向的风荷载。 The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
施加集中质量的细长梁,并施加一个随时间变化的力。 It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
在一根方形截面的钢梁上施加轴力和均布荷载。 The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
一个两端开口的双层厚壁容器承受内部和外部压力; ,即正应力为零。 While neglecting self‑weight, the radial deflection of the inner and outer radius, and the pressure (radial stress) in the middle radius is determined.
该类型的悬臂梁截面为矩形,在端部有一个质量块。 Furthermore, it is loaded by an axial force. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
证明耦合不同尺寸的单元不会影响结果。 A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
对厚壁容器施加内部压力,使得该容器达到弹塑性状态。 While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
截面为 ASTM A992 W 18×50 的梁用于跨度和均布活荷载,如图 1 所示。 The member is limited to a maximum nominal depth of 18 inches. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Ein Kehlbaken Dach mit gewählter geometrie wird in Hinblick auf seine Schnittgrößen zwischen Berechnung mittels RFEM 6 und der Handrechnung verglichen. Dabei werden insgesamt 3 最后一个未验算的系统。
施加阻尼器的单质量系统受到恒定的力。 Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
在两个同心圆柱体的两个半径半径之间的各向同性预应力拉伸膜,该预应力位于一个不与竖轴平行的平面上。 Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
定义悬臂梁为工字形,截面长度为 L。 The beam has five mass points with masses m acting in the X-direction. The self-weight is neglected. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.