20 结果
查看结果:
排序方式:
在本文中,使用附加模块 RF-/TIMBER AWC 验证了一个 2x4 尺寸的木材在承受双轴受弯和轴压组合作用的充分性。 梁柱属性和荷载基于 AWC 2015/2018 中木结构设计实例 E1.8 计算得出。
Im Zuge einer sinnvollen Vordimensionierung der Querschnitte ist es im Modul RF-/HOLZ Pro möglich, die Querschnitte der entsprechenden Profilreihe zu optimieren.
The National Building Code of Canada (NBC) 2015 Article 4.1.8.7 provides a clear procedure for earthquake methods of analysis. The more advanced method, the Dynamic Analysis Procedure in Article 4.1.8.12, should be used for all structure types except those that meet the criteria set forth in 4.1.8.7. The more simplistic method, the Equivalent Static Force Procedure (ESFP) in Article 4.1.8.11, can be used for all other structures.
Using the RF-TIMBER CSA module, timber column design is possible according to the CSA O86-19 standard. Accurately calculating timber member compressive resistance and adjustment factors is important for safety considerations and design. The following article will verify the factored compressive resistance in the RFEM add-on module RF-TIMBER CSA, using step-by-step analytical equations as per the CSA O86-19 standard including the column modification factors, factored compressive resistance, and final design ratio.
使用模块 RF-TIMBER AWC,可以按照 2018 NDS 标准 ASD 方法进行木柱设计。 准确计算木杆件的抗压承载力和调整系数对于安全考虑和设计非常重要。 以下文章将按照 NDS 2018 标准,使用逐步验算的验算方程对 RF-TIMBER AWC 的最大临界屈曲进行验算,包括受压调整系数、调整后的抗压设计值和最终设计利用率。
Using the RF-TIMBER CSA module, timber beam design is possible according to the CSA O86-14 standard. Accurately calculating timber member bending resistance and adjustment factors is important for safety considerations and design. The following article will verify the factored bending moment resistance in the RFEM add-on module RF-TIMBER CSA using step-by-step analytical equations as per the CSA O86-14 standard including the bending modification factors, factored bending moment resistance, and final design ratio.
使用模块 RF-TIMBER AWC,可以按照 2018 NDS 标准 ASD 方法进行木梁设计。 准确计算木杆件抗弯承载力和调整系数对于安全考虑和设计非常重要。 以下文章将按照 NDS 2018 标准,使用计算公式逐步验证 RF-TIMBER AWC 中的最大临界屈曲屈曲值,包括受弯调整系数、调整后的受弯设计值和最终设计比率。
美国木材协会(AWC)发布了 2018 年版的木结构国家设计规范(NDS)。 This is the second edition of the NDS to contain a chapter dedicated to cross-laminated timber (CLT) design. Therefore, a couple of revisions were included in the 2018 NDS when compared to the previous 2015 Edition.
说到 ASCE 7 中建筑结构上的风荷载,可以找到大量的资源来补充设计规范和帮助工程师处理这种侧向荷载。 However, engineers may find it more difficult to find similar resources for wind loading on non-building type structures. This article will examine the steps to calculate and apply wind loads as per ASCE 7-16 on a circular reinforced concrete tank with a dome roof.
使用 RF-/JOINTS Timber - Timber to Timber 木结构连接节点附加模块可以计算主梁与次梁连接节点设计。 本例题阐述如何计算某连接于不受扭矩作用的主梁上的次梁节点位置上各个螺栓所受的荷载。
对于连接件受拉连接的单侧连接,由于偏心荷载分布,外部杆件(侧木)承受一个附加弯矩。 Dieser Umstand wird jedoch in EN 1995-1-1 nicht erwähnt und wurde zum Beispiel im Nationalen Anhang zu DIN EN 1995-1-1 durch eine Abminderung der Zugfestigkeit berücksichtigt. Diese Abminderung ist abhängig von der Ausziehfestigkeit des Verbindungsmittels.
从附加模块 RF‑/TIMBER AWC 和 RF‑/TIMBER CSA 的版本 X.06 开始可以在设计中考虑切口和截面折减。 Die Vorgehensweise ist wie folgt.
在 RF-/JOINTS Timber – Steel to Timber 中的钢筋连接、螺栓连接、钉子连接和螺栓连接类别中可以选择圆形连接类型。 Bei dieser Anschlussform wird ein Mindestradius entsprechend der Empfehlungen des STEP-1-Berichts des Informationsdienstes Holz umgesetzt.
在附加模块 RF-/TIMBER Pro 中也可以定义弯扭屈曲的有效长度。 Die Kipplänge wird dabei gemäß EN 1995-1-1 Tabelle 6.1 berechnet. Insbesondere bei einer ungleichmäßigen Lasteinleitung ist diese Option sinnvoll.
模块 RF-/STEEL EC3 和模块 RF-/TIMBER Pro 不仅可以进行截面验算和稳定性分析,还可以进行正常使用极限状态设计。 Hierzu können die Verformungen auf das unverformte Ausgangssystem oder die verschobenen Stabenden bezogen werden.
自版本 X.04.0096 起,使用 RF-/TIMBER Pro 也可以设计其他材料类别,例如阔叶木、阔叶木和层板胶合木作为一根杆件设计(按照欧洲规范 EN 1995-1-1)。 Das Bemessungsspektrum wurde für die Material-Kategorien LVL, Sperrholz, OSB-/Faser-/Spanplatten erweitert. Um die Auswahl in der Materialbibliothek zu erleichtern, wurde dort ein weiterer Filter eingebaut, mit welchem sich gezielt nach der Eigenschaft Platten- oder Scheibenbeanspruchung filtern lässt.
在 RF-/JOINTS Timber - Steel to Timber 中计算节点的偏心时可以考虑。 Im Bild sind die unterschiedlichen Schnittgrößen ohne Berücksichtigung der Exzentrizität (oben) und mit Berücksichtigung der Exzentrizität (unten) zu sehen.
在附加模块 RF-/JOINTS Timber 中可以不将计算中的某个连接销进行计算。 Bei der Berechnung werden diese entfernten Stabdübel neben der Tragfähigkeitsberechnung auch bei den Netto-Holzquerschnitten sowie auch bei der Ermittlung der Drehfedersteifigkeit vernachlässigt.