Una membrana se estira por medio de un pretensado isótropo entre dos radios de dos cilindros concéntricos que no se encuentran en un plano paralelo al eje vertical. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Consider an ASTM A992 W 18×50 beam forspan and uniform dead and live loads as shown in Figure 1. La barra está limitada a un canto nominal máximo de 18 pulgadas. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
A thin rectangular orthotropic plate is simply supported and loaded by uniformly distributed pressure. The directions of axes x and y coincide with the principal directions. Determine la deformación máxima de la placa sin considerar el peso propio.
Una viga curva consta de dos vigas con una sección rectangular. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
Un oscilador simple consta de una masa m (considerada solo en la dirección x) y un muelle lineal de rigidez k. The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
Un muro de fábrica está expuesto a una carga distribuida en el medio de su sección superior. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
A structure is made of two trusses of unequal length, which are embedded into the hinge supports. The structure is loaded by concentrated force. Se omite el peso propio. Determine the relationship between the loading force and the deflection, considering large deformations.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Una viga larga y delgada lleva una masa concentrada y está cargada por una fuerza dependiente del tiempo. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
Una viga de madera reforzada con dos placas de acero en los extremos está cargada por presión. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
A structure is made of two trusses, which are embedded into the hinge supports. The structure is loaded by concentrated force. Se omite el peso propio. Determine the relationship between the loading force and the deflection, considering large deformations.
Una estructura hecha de cerchas de perfil en I está apoyada en ambos extremos mediante apoyos deslizantes de muelles y cargada por fuerzas transversales. The self-weight is neglected in this example. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
Un voladizo de perfil en I está apoyado en el extremo izquierdo y cargado por el par. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).
Un bloque tridimensional hecho de material elástico-plástico está fijado en ambos extremos. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Determinar la flecha máxima de un bloque tridimensional fijo en ambos extremos. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. The block's middle plane is subjected to vertical pressure.
Una viga de madera reforzada con dos placas de acero en los extremos está cargada por presión. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Un bloque tridimensional hecho de material elástico-plástico con endurecimiento está fijado en ambos extremos. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.