Un voladizo de una sección rectangular se encuentra sobre un apoyo elástico de Winkler y se carga mediante una carga distribuida. The image shows the calculation of the maximum deflection and maximum bending moment.
Una viga de acero con una sección cuadrada está cargada con un esfuerzo axil y una carga distribuida. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Una viga de acero cargada axialmente con una sección cuadrada está articulada en un extremo y apoyada en un muelle en el otro. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
Una viga de madera reforzada con dos placas de acero en los extremos está cargada por presión. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Un voladizo está completamente fijo en el extremo izquierdo y cargado por una fuerza transversal y una fuerza axil en el extremo derecho. The tensile strength is zero and the behavior in the compression remains elastic.
Una placa ancha con un agujero está cargada en una dirección por la tensión de tracción. The plate width is large with respect to the hole radius, and it is very thin, considering the state of the plane stress.
Una viga de madera reforzada con dos placas de acero en los extremos está cargada por presión. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Cuatro pilares están fijos en la parte inferior y conectados por un bloque rígido en la parte superior. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Un voladizo de sección variable está completamente fijado en el extremo izquierdo y cargado por una carga continua. Plastic material is considered for the calculation.
Un cable o membrana de acero con pasadores en ambos extremos se carga mediante una carga distribuida. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
Un voladizo vertical con una sección cuadrada está cargado en la parte superior por la presión de tracción. The cantilever consists of an isotropic material. Calculate the deflection.
Una estructura hecha de cerchas de perfil en I está apoyada en ambos extremos mediante apoyos deslizantes de muelles y cargada por fuerzas transversales. The self-weight is neglected in this example. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
Una viga está completamente fija (el alabeo está restringido) en el extremo izquierdo y está apoyada en un apoyo en horquilla (el alabeo está habilitado) en el extremo derecho. The beam is subjected to a torque, longitudinal force, and transverse force. Determine the behavior of the primary torsional moment, secondary torsional moment, and warping moment. The verification example is based on the example introduced by Gensichen and Lumpe.
Una viga articulada en ambos extremos está cargada con una fuerza concentrada en el medio. Neglecting its self-weight and shear stiffness, determine the beam's maximum deflection, normal force, and moment at the mid-span, assuming the second- and third-order analysis.
Un voladizo de perfil en I está apoyado en el extremo izquierdo y cargado por el par. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Se omite el peso propio. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Un voladizo de una sección rectangular se encuentra sobre una cimentación elástica de Pasternak y se carga mediante una carga distribuida. The image shows the calculation of the maximum deflection and maximum bending moment.
Una placa compuesta que consta de tres capas de vidrio, una capa de lámina y un espacio interior con aire seco, está completamente fijada y cargada con una temperatura variable. Neglecting its self-weight, determine the plate's maximum deflection.
Un muro de fábrica está expuesto a una carga distribuida en el medio de su sección superior. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Una consola está cargada por una fuerza concentrada en su extremo libre. Determine the maximum deflection of the console using large deformation analysis.
Un voladizo está cargado por una fuerza transversal y axil en el extremo derecho y está completamente fijo en el extremo izquierdo. The problem is described by the following set of parameters. The problem is solved by using the geometrically linear analysis, second-order analysis, and large deformation analysis.
Una barra ligeramente inclinada está cargada por una fuerza concentrada, sostenida por un muelle en un extremo y apoyada en el otro extremo. Assuming large deformations and neglecting the member's self-weight, determine its maximum upward deflection.
Un voladizo está cargado por un momento en su extremo libre. Using the geometrically linear analysis and large deformation analysis, and neglecting the beam's self-weight, determine the maximum deflections at the free end. The verification example is based on the example introduced by Gensichen and Lumpe.
Una barra con las condiciones de contorno dadas está cargada por el momento torsor y el esfuerzo axil. Neglecting its self-weight, determine the beam's maximum torsional deformation as well as its inner torsional moment, defined as the sum of a primary torsional moment and torsional moment caused by the normal force. Provide a comparison of those values while assuming or neglecting the influence of the normal force. The verification example is based on the example introduced by Gensichen and Lumpe.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum deflection with consideration of initial slippage.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Una viga larga y delgada lleva una masa concentrada y está cargada por una fuerza dependiente del tiempo. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
El objetivo de este ejemplo es demostrar un proceso irreversible causado por la fricción. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.