Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum deflection with consideration of initial slippage.
Determinar la flecha máxima y el momento radial máximo de una placa circular simplemente apoyada sometida a presión uniforme, temperatura uniforme y temperatura diferencial.
Una viga larga y delgada lleva una masa concentrada y está cargada por una fuerza dependiente del tiempo. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
Una placa ortótropa cuadrada en capas está completamente fijada en su punto medio y sometida a presión. Compare las flechas de las esquinas de la placa para comprobar la corrección de la transformación.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Una viga de acero con una sección cuadrada está cargada con un esfuerzo axil y una carga distribuida. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Una consola hecha de un redondo está cargada por una carga uniforme excéntrica. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
Un recipiente de paredes gruesas está cargado por una presión interna tal que el recipiente alcanza un estado elástico-plástico. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
Un voladizo está completamente fijo en el extremo izquierdo y cargado por una fuerza transversal y una fuerza axil en el extremo derecho. The tensile strength is zero and the behavior in the compression remains elastic.
Un sistema monomasa con amortiguador está sometido a una fuerza de carga constante. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Determine las flechas máximas del bloque considerando o omitiendo el efecto cortante. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Determine la flecha y la tensión máximas en la dirección z de la placa mixta, que consta de dos capas de vidrio y una capa de lámina intermedia, sometidas a una presión uniforme.
Una placa compuesta que consta de tres capas de vidrio, una capa de lámina y un espacio interior con aire seco, está completamente fijada y cargada con una temperatura variable. Neglecting its self-weight, determine the plate's maximum deflection.
Un disco compacto (CD) gira a una velocidad de 10.000 rpm. Therefore, it is subjected to centrifugal force. The problem is modeled as a quarter model. Determine the tangential stress on the inner and outer diameters and the radial deflection of the outer radius.
Determinar la flecha máxima de un bloque tridimensional fijo en ambos extremos. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. The block's middle plane is subjected to vertical pressure.
Un voladizo está completamente fijado en el extremo izquierdo y cargado por un momento flector en el extremo derecho. El material tiene diferentes resistencias plásticas a tracción y compresión.
El objetivo de este ejemplo es demostrar un proceso irreversible causado por la fricción. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.
Un recipiente de dos capas, de extremos abiertos y paredes gruesas está cargado por una presión interna y externa; por lo tanto, no hay tensión axil. While neglecting self‑weight, the radial deflection of the inner and outer radius, and the pressure (radial stress) in the middle radius is determined.
Una placa delgada está completamente fija en el extremo izquierdo y cargada con una presión uniforme. El material plástico se considera para el cálculo.
Demuestre que el acoplamiento de diferentes elementos dimensionales no afecta a los resultados. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
Considere una conexión de tubo de andamio sometida a un esfuerzo axil y un momento. Self-weight is not considered. The material of the tube is idealized as perfectly rigid. All geometrical non-linearities are ignored. Determine the angle of deflection.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Se omite el peso propio. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Determinar el desplazamiento máximo, las tensiones en el plano y las relaciones de tensiones de una placa de vidrio de doble panel simplemente apoyada con una lámina entre ambos paneles de vidrio sometida a una presión uniforme.
A structure is made of two trusses of unequal length, which are embedded into the hinge supports. The structure is loaded by concentrated force. Se omite el peso propio. Determine the relationship between the loading force and the deflection, considering large deformations.
Cuatro pilares están fijos en la parte inferior y conectados por un bloque rígido en la parte superior. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Una placa ortótropa cuadrada en capas está completamente fijada en su punto medio y sometida a presión. Compare the deflections of the plate corners to check the correctness of the transformation.
Una barra con una sección cuadrada está fijada en el extremo superior. The rod is loaded by self-weight. For comparison, the example is also modeled with the concentrated force load, the value of which is equal to the gravity. The aim of this verification example is to show the difference between these types of loading, although the total loading force is equal.