Un voladizo ahusado se fija completamente en el extremo izquierdo y se somete a una carga continua q. Se consideran las pequeñas deformaciones y se desprecia el peso propio en este ejemplo. Determine la flecha máxima.
A thin rectangular orthotropic plate is simply supported and loaded by uniformly distributed pressure. The directions of axes x and y coincide with the principal directions. Determine la deformación máxima de la placa sin considerar el peso propio.
Una placa delgada se fija completamente en el extremo izquierdo y se somete a una presión uniforme. La placa se lleva al estado elástico-plástico mediante la presión uniforme.
Una viga articulada con una sección rectangular está sometida a una carga distribuida y desplazada verticalmente por la excentricidad. Considering the small deformation theory, neglecting the self‑weight, and assuming that the beam is made of isotropic elastic material, determine the maximum deflection.
Un muro de fábrica está expuesto a una carga distribuida en el medio de su sección superior. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Una membrana cilíndrica se estira por medio de un pretensado isótropo. Find the final minimal shape of the membrane - catenoid. Determine the maximum radial deflection of the membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Un voladizo con fibras que no discurren en dirección del eje de la viga desde una sección cuadrada con presión de tracción. Calculate the maximum deflection.
Un bloque tridimensional hecho de material elástico-plástico está fijado en ambos extremos. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Determine la flecha máxima de cuatro pilares fijos en la parte inferior y conectados por un bloque rígido en la parte superior. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
Un voladizo de sección variable está completamente fijado en el extremo izquierdo y cargado por una carga continua. Plastic material is considered for the calculation.
Una placa delgada está completamente fija en el extremo izquierdo y cargada con una presión uniforme. El material plástico se considera para el cálculo.
Una membrana de globo esférico se llena con gas con presión atmosférica y volumen definido (estos valores se usan solo para la definición del modelo de elementos finitos). Determine the overpressure inside the balloon due to the given isotropic membrane prestress. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Una placa ortótropa cuadrada en capas está completamente fijada en su punto medio y sometida a presión. Compare the deflections of the plate corners to check the correctness of the transformation.
Un bloque tridimensional hecho de material elástico-plástico con endurecimiento está fijado en ambos extremos. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
Una estructura de pórtico de un solo vano de dos plantas está sometida a una carga sísmica. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
Determinar la flecha máxima de un bloque tridimensional fijo en ambos extremos. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. The block's middle plane is subjected to vertical pressure.
Cuatro pilares están fijos en la parte inferior y conectados por un bloque rígido en la parte superior. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Un voladizo está completamente fijado en el extremo izquierdo y cargado por un momento flector en el extremo derecho. El material tiene diferentes resistencias plásticas a tracción y compresión.
Un sistema monomasa con amortiguador está sometido a una fuerza de carga constante. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Un cable está cargado por medio de una carga uniforme. This causes the deformed shape in the form of the circular segment. Determine the equilibrium force of the cable to obtain the given sag of the cable. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Un voladizo está completamente fijo en el extremo izquierdo y cargado por una fuerza transversal y una fuerza axil en el extremo derecho. The tensile strength is zero and the behavior in the compression remains elastic.
Una membrana se estira por medio de un pretensado isótropo entre dos radios de dos cilindros concéntricos que no se encuentran en un plano paralelo al eje vertical. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Una placa ortótropa cuadrada en capas está completamente fijada en su punto medio y sometida a presión. Compare las flechas de las esquinas de la placa para comprobar la corrección de la transformación.
Este ejemplo de verificación se basa en el ejemplo de verificación 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.