97x
004208
0001-01-01
11 Program Functions

4.8 Line Supports

General description

Line supports describe the boundary conditions of all FE nodes available along a line: Displacements and rotations on these internal nodes can be prevented or limited by translational and rotational springs.

You can assign nonlinear properties to displacements of line supports so that supports are ineffective in case of tension or compression.

Image 4.102 New Line Support dialog box
Image 4.103 Table 1.8 Line Supports

Use the menu option Insert → Model Data → Line Supports → Graphically or the toolbar button shown on the left to open the following dialog box:

Image 4.104 New Line Support dialog box

The support types Hinged (YYY NNN) and Rigid (YYY YYY) are predefined and can be selected from the list. After clicking [OK], you can graphically assign the selected support type to the lines.

Use the [New] button to create another type of support. The dialog box shown in Figure 4.100 is displayed.

On Lines No.

Line supports can only be defined on lines that belong to a surface or a solid. Enter the line number into the table column or text box of the dialog box, or select it graphically.

Reference System

The support parameters can be related Locally to the line axes x,y,z or Globally to the axes X,Y,Z. Indexes in the Support Conditions dialog section as well as headlines of table columns E to J change depending on the selected setting.

Shortcut menu of line support

The display of the local axis system of lines including numbering can be set in the Display navigator. You can also use the shortcut menu of a line support.

Image 4.105 Activating the local line axis systems x,y,z in the Display navigator
Support rotation

It is possible to rotate the axis system of a local line support. The Rotation about a positive angle β rotates the support clockwise around the positive line axis x.

Image 4.106 Support rotation

The entered support rotation is shown in the dynamic dialog graphic.

Note

When the calculation is complete, it is possible to evaluate support reactions of a rotated line support in relation to the global and the local axis system.

Wall in Z

When a surface is supported by a wall, it is considered an elastic support that depends on the stiffness of the wall. A fixed line support would not represent the flexibility correctly. For such a support type, you can define a Wall: RFEM calculates the constants of translational and rotational springs from the wall's material and geometry. This option is especially useful for 2D plates in order to avoid singularities, which would occur for a rigidly supported line.

Image 4.107 Edit Wall dialog box

Define the geometry in the Wall Size dialog section. In addition to the Width t, the Height h affects the constants of the translational and rotational springs.

In the Parameters dialog section, select the Material of wall from the list of already defined materials or create a [New] wall material (see Chapter 4.3).

To determine the spring stiffnesses, specifications for Support conditions at wall head and wall base are required. If you consider the shear stiffness of the wall, it is also considered for the constants of the Support Springs Due to Wall.

The spring constants determined from the parameters are displayed on the right in the dialog box.

The wall widths on the supported line are displayed in the RFEM graphic.

Support or Spring

To define a support, select the corresponding option in the dialog box or table. The check mark indicates that the relevant degree of freedom is blocked and the line displacement in the respective direction is not possible.

If you do not want to define supports, clear the corresponding check box. RFEM sets the constant of the translational spring to zero in the Line Support dialog box. The spring constant can be modified anytime, in order to represent an elastic support of the line. In the table, enter the constant directly into the table column.

Note

The spring stiffnesses are considered design values.

Assigning a failure criterion is described below.

Restraint or Spring

Restraints are defined analogously to supports. Again, the check mark indicates that the relevant degree of freedom is blocked and the line displacement in the respective direction is not possible. In the same way, the constants for rotational springs can be defined once the check boxes are cleared. In the table, enter the spring constant directly into the corresponding table column.

Note

The New Line Support dialog box (see Figure 4.100) provides buttons for different support types, making the definition of degrees of freedom easier.

Image 4.108 Buttons in the New Line Support dialog box

The buttons have the following functions for support properties:

Table 4.4 Line Support buttons
Button Support Type

Rigid

Hinged with restraint about Z'

Sliding in X' and Y' with restraint about Z'

Sliding in X' with restraint about Z'

Sliding in Y' with restraint about Z'

Sliding in Z' and Y' with restraint about Z'

Free

Nonlinearities

You can assign the following nonlinear properties to the components of a line support:

    • Failure of component if support force or moment is negative or positive
    • Complete failure of support if support force or moment is negative or positive
    • Partial activity
    • Diagram
    • Friction depending on remaining support forces

The nonlinear properties essentially correspond to the nonlinearities available for nodal supports (see Chapter 4.7).

The nonlinear properties can be accessed in the dialog box and table by using the list (see Figure 4.100 and Figure 4.101). For each of the support's degree of freedom, you can define whether and which forces or moments are transferred on the supported line using these settings.

Positive or negative refers to the forces that are introduced to the support in direction of the respective axes (they do not refer to the reaction forces of the line support). The algebraic signs therefore result from the direction of the local or global axes. For example, if the local z-axis of a line is directed downwards, the load case "Self-weight" results in a positive support force pZ'.

Nonlinear effective supports of lines are displayed with a different color in the graphic. In the table, you can recognize support elements with a failure criterion by a blue check box.

上级章节