Una estructura consta de una viga de sección en I y dos cerchas tubulares. The structure contains several imperfections and it is loaded by the force Fz. El peso propio se omite en este ejemplo. Determine the deflections uy and uz and axial rotation φx at the endpoint (Point 4). El ejemplo de verificación se basa en el ejemplo presentado por Gensichen y Lumpe.
Este ejemplo compara las longitudes eficaces y el factor de carga crítica, que se pueden calcular en RFEM 6 utilizando el complemento Estabilidad de la estructura, con un cálculo manual. El sistema estructural es un pórtico rígido con dos pilares articulados adicionales. Este pilar está cargado por cargas puntuales verticales.
Una viga de hormigón armado se calcula como una viga de dos vanos con un voladizo. La sección varía a lo largo del voladizo (sección de sección variable). Se calculan los esfuerzos internos, la armadura longitudinal necesaria y la armadura de cortante para el estado límite último.
En este ejemplo de verificación, los valores de cálculo de la capacidad de los esfuerzos cortantes en vigas se calculan según EN 1998-1, 5.4.2.2 y 5.5.2.1, así como los valores de cálculo de la capacidad de los pilares en flexión según 5.2.3.3(2 ). El sistema consiste en una viga de hormigón armado de dos vanos con una longitud de vano de 5,50 m. La viga es parte de un sistema de pórtico. Los resultados obtenidos se comparan con los de [1].
Se calcula un pilar interior en el primer piso de un edificio de tres plantas. El pilar es monolítico conectado con las vigas superior e inferior. El método simplificado de cálculo frente al fuego A para pilares según EC2-1-2 se ha probado y los resultados se comparan con [1].
Los asentamientos de una cimentación cuadrada rígida sobre una arcilla lacustre Refer [1] se calculan con RFEM. Se modela una cuarta parte de la cimentación. La cimentación tiene un ancho de 75,0 m en ambos lados. Las etapas de construcción se utilizan para generar los resultados.
Las normas disponibles, como EN 1991-1-4 [1], ASCE/SEI 7-16 y NBC 2015 presentaron parámetros de carga de viento como el coeficiente de presión del viento (Cp) para formas básicas. El punto importante es cómo calcular los parámetros de la carga de viento de forma más rápida y precisa, en lugar de trabajar en fórmulas de las normas que requieren mucho tiempo y, a veces, son complicadas.
Una estructura hecha de un perfil en I está incrustada en los apoyos de la horquilla. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
Una estructura superficial simétrica se compone de ocho barras de celosía iguales, que están incrustadas en los apoyos de las articulaciones. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
Una estructura se compone de cuatro barras de celosía, que están incrustadas en apoyos de articulación. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Una estructura de celosía consta de tres barras (una de acero y dos de cobre) unidas por una barra rígida. The structure is loaded by a concentrated force and a temperature difference. While neglecting self‑weight, determine the total deflection of the structure.
Un voladizo de sección rectangular tiene una masa al final. Furthermore, it is loaded by an axial force. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Una estructura de pórtico de un solo vano de dos plantas está sometida a una carga sísmica. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
Este ejemplo sirve como demostración de la coacción del diafragma. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
Un voladizo de una sección rectangular se encuentra sobre una cimentación elástica de Pasternak y se carga mediante una carga distribuida. The image shows the calculation of the maximum deflection and maximum bending moment.
Un muro de fábrica está expuesto a una carga distribuida en el medio de su sección superior. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
A structure is made of two trusses of unequal length, which are embedded into the hinge supports. The structure is loaded by concentrated force. Se omite el peso propio. Determine the relationship between the loading force and the deflection, considering large deformations.
Una estructura hecha de un perfil en I está completamente fijada en el extremo izquierdo y empotrada en el apoyo deslizante en el extremo derecho. The structure consists of two segments. The self-weight is neglected in this example. Determine the maximum deflection of the structure, the bending moment on the fixed end, the rotation of segment 2, and the reaction force at point B by means of the geometrically linear analysis and the second-order analysis. The verification example is based on the example introduced by Gensichen and Lumpe.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum deflection with consideration of initial slippage.
Considere un tubo de andamio rígido, fijado en la parte inferior utilizando el apoyo en nudo de andamio y cargado tanto por un momento como por una fuerza. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Análisis en el dominio del tiempo de una viga en voladizo (sistema SDOF) excitada por una función periódica. Vertical deformations and accelerations calculated with direct integration and modal analysis in RF‑/DYNAM Pro - Forced Vibrations are compared with the analytical solution.
Cuatro pilares están fijos en la parte inferior y conectados por un bloque rígido en la parte superior. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Un voladizo de sección variable está completamente fijado en el extremo izquierdo y cargado por una carga continua. Plastic material is considered for the calculation.
Un cable o membrana de acero con pasadores en ambos extremos se carga mediante una carga distribuida. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
Un voladizo vertical con una sección cuadrada está cargado en la parte superior por la presión de tracción. The cantilever consists of an isotropic material. Calculate the deflection.
A structure is made of two trusses, which are embedded into the hinge supports. The structure is loaded by concentrated force. Se omite el peso propio. Determine the relationship between the loading force and the deflection, considering large deformations.
Una estructura hecha de cerchas de perfil en I está apoyada en ambos extremos mediante apoyos deslizantes de muelles y cargada por fuerzas transversales. The self-weight is neglected in this example. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
Un voladizo de acero con una sección rectangular está completamente fijo en un lado y libre en el otro. The aim of this verification example is to determine the natural frequencies of the structure.
Una estructura de celosía plana está simplemente apoyada. The aim of this verification example is to determine the natural frequencies of the structure.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Se omite el peso propio. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.