Dans cet exemple, nous comparons les longueurs efficaces et le facteur de charge critique, qui peuvent être calculés dans RFEM 6 à l'aide du module complémentaire Stabilité de la structure, avec un calcul manuel. La structure est un portique rigide avec deux poteaux articulés. Ce poteau est chargé par des charges verticales concentrées.
Une dalle en béton armé à l'intérieur d'un bâtiment doit être calculée comme une bande de 1,0 m avec des barres. Le radier est à travée uniaxiale et traverse deux travées. La dalle est fixée sur des murs en maçonnerie avec des appuis libres. L'appui central a une largeur de 240 mm et les deux appuis latéraux ont une largeur de 120 mm. Les deux travées sont soumises à une charge imposée de catégorie C : zones de rassemblement.
Un cylindre constitué de sol élasto-plastique est soumis à des conditions de test triaxiales. L'objectif est de déterminer la contrainte verticale limite pour l'échec de contrainte de cisaillement en négligeant le poids propre. Une contrainte hydrostatique initiale de 100 kPa est considérée.
Une bielle de section circulaire est supportée selon quatre cas de base de flambement selon Euler et est soumise à une force de pression. Determine the critical load.
A symmetrical shallow structure is made of eight equal truss members, which are embedded into hinge supports. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. Le poids propre est négligé dans cet exemple. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
A structure is made of four truss members, which are embedded into hinge supports. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. Le poids propre est négligé dans cet exemple. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Un poteau est composé d'une section en béton (rectangle 100/200) et d'une section en acier (profilé I 200). It is subjected to pressure force. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
A thin circular ring of a rectangular cross-section is exposed to external pressure. Déterminez la charge critique et le facteur de charge correspondant pour le flambement dans le plan.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. le poids propre est négligé. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Déterminez analytiquement le moment d'inertie de torsion de la section du tuyau et comparez les résultats avec la solution numérique dans RFEM 5 et RSTAB 8 pour différentes épaisseurs de paroi.
Une poutre en acier de section carrée est chargée avec un effort normal et une charge répartie. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Une poutre en acier chargée axialement avec une section carrée est fixée à une extrémité et supportée par un ressort à l'autre. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.