Das Architectural Institute of Japan (AIJ) hat eine Reihe an bekannten Benchmark-Szenarien für Windsimulation vorgestellt.
Der Nachfolgende Beitrag dreht sich dabei um den « Cas A - Immeuble de grande hauteur de forme 2:1:1 ».
Im Folgenden wird das beschriebene Szenario in RWIND2 nachgebildet und die Ergebnisse mit den simulierten und der experimentellen Resultate des AIJ verglichen.
Une plaque rectangulaire sur appuis simples est chargée de différents types de charge. Assuming only the small deformation theory and neglecting self-weight, determine the deflection at its centroid for each load type.
Une bande bi métallique est composée d'invar et de cuivre. The left end of the bimetallic strip is fixed, and the right end is free, loaded by temperature difference. While neglecting self-weight, determine the deflection of the bimetallic strip (free end).
Cet exemple de vérification compare le calcul des charges de vent sur un bâtiment avec une toiture à deux versants selon la norme ASCE 7-16 et celui de la simulation CFD dans RWIND Simulation. The building is defined according to the sketch and the inflow velocity profile taken from the ASCE 7-16 standard.
The verification example compares wind load calculation on a building with a flat roof using the standard EN 1991-1-4 and using CFD simulation in RWIND Simulation. Le bâtiment est défini d'après le croquis et le profil de vitesse d'afflux est calculé selon la norme EN 1991-1-4.
Cet exemple de vérification compare le calcul des charges de vent sur une toiture terrasse selon la norme ASCE 7-16 et celui de la simulation CFD dans RWIND Simulation. The building is defined according to the sketch and the inflow velocity profile taken from the ASCE 7-16 standard.
L'exemple de vérification compare le calcul de la charge de vent sur un bâtiment avec une toiture à deux versants à l'aide de la norme EN 1991-1-4 et de la simulation CFD dans RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. le poids propre est négligé. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Cet exemple sert de démonstration du couplage de diaphragme. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
Montrer que le couplage de différents éléments dimensionnels n'affecte pas les résultats. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
Une poutre sur appuis simples est chargée en flexion seule. Determine the critical load and corresponding load factor due to lateral buckling.
Déterminez les flèches maximales du bloc en considérant ou en négligeant l'effet de cisaillement. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
L'Institut d'architecture du Japon (AIJ) a présenté un certain nombre de scénarios de référence bien connus de la simulation du vent.
L'article suivant traite du « Cas D - Immeuble de grande hauteur entre des îlots urbains ».
Le scénario décrit ci-dessous est simulé dans RWIND2 et les résultats sont comparés aux résultats simulés et expérimentaux de l'AIJ.
L'Institut d'architecture du Japon (AIJ) a présenté un certain nombre de scénarios de référence bien connus de la simulation du vent.
L'article suivant porte sur le « Cas E - un complexe immobilier dans une zone urbaine avec une forte concentration de bâtiments de faible hauteur dans la ville de Niigata ».
Le scénario décrit ci-dessous est simulé dans RWIND2 et les résultats sont comparés aux résultats simulés et expérimentaux de l'AIJ.
Une bielle de section circulaire est supportée selon quatre cas de base de flambement selon Euler et est soumise à une force de pression. Determine the critical load.
Un poteau est composé d'une section en béton (rectangle 100/200) et d'une section en acier (profilé I 200). It is subjected to pressure force. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
Déterminez le moment fléchissant qui, agissant à l'extrémité libre du porte-à-faux, fléchit la barre en forme circulaire. Neglecting the beam's self-weight, assuming the large deformation analysis, and loading the cantilever with the moment, determine its maximum deflections.
Une structure faite de profilé en I est intégrée dans les appuis des fourches. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
L'exemple de vérification décrit des charges de vent dans plusieurs directions du vent sur un modèle de groupe de bâtiments. Le modèle est composé de huit cubes. Les champs de vitesse obtenus par la simulation de RWIND sont comparés aux valeurs mesurées issues de l'expérience. Les données expérimentales sont mesurées à l'aide d'un anémomètre à thermistance dans la soufflerie.
Cet exemple est une modification de l'exemple de vérification 0061 ; la seule différence est que le matériau du réservoir est incompressible. An open‑ended, thick‑walled vessel is loaded by both inner and outer pressure. While neglecting self‑weight, the radial deflection of the inner and the outer radius is determined.
A symmetrical shallow structure is made of eight equal truss members, which are embedded into hinge supports. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. Le poids propre est négligé dans cet exemple. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
Déterminez la flèche maximale de quatre poteaux encastrés en bas et connectés par un bloc rigide en haut. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
Un bloc tridimensionnel en matériau élastique-plastique est fixé aux deux extrémités. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Un bloc tridimensionnel en matériau élastique-plastique avec durcissement est fixé aux deux extrémités. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
Une barre de section carrée est fixée à l'extrémité supérieure. The rod is loaded by self-weight. For comparison, the example is also modeled with the concentrated force load, the value of which is equal to the gravity. The aim of this verification example is to show the difference between these types of loading, although the total loading force is equal.
A structure is made of four truss members, which are embedded into hinge supports. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. Le poids propre est négligé dans cet exemple. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Une poutre en bois renforcée par deux plaques en acier aux extrémités est chargée en pression. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Une poutre courbe est composée de deux poutres de section rectangulaire. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
Une poutre en bois renforcée par deux plaques en acier aux extrémités est chargée en pression. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
A vertical cantilever with a square cross-section is loaded at the top by tensile pressure. Le porte-à-faux est en matériau isotrope. Calculate the deflection.