Une poutre est entièrement encastrée (gauchissement limité) à l'extrémité gauche et supportée par un appui à fourche (gauchissement libre) à l'extrémité droite. La poutre est soumise à un moment de torsion, une force longitudinale et une force transversale. Déterminer le comportement du moment de torsion primaire, du moment de torsion secondaire et du moment de gauchissement. L'exemple de vérification est basé sur l'exemple introduit par Gensichen et Lumpe (voir la référence).
L'Institut d'architecture du Japon (AIJ) a présenté un certain nombre de scénarios de référence bien connus de la simulation du vent. L'article suivant porte sur le « Cas E - un complexe immobilier dans une zone urbaine avec une forte concentration de bâtiments de faible hauteur dans la ville de Niigata ». Le scénario décrit ci-dessous est simulé dans RWIND2 et les résultats sont comparés aux résultats simulés et expérimentaux de l'AIJ.
L'exemple de vérification décrit les charges de pression sur les voiles des bâtiments disposés en parallèle au niveau du sol. The buildings are simplified to rectangular objects and scaled down while maintaining the elevation ratios. The pressure distribution on the walls of the model of a medium-high building was conducted by an experiment. The chosen results (pressure coefficient Cp) are compared with the measured values.
L'exemple de vérification décrit le flux stationnaire autour d'un bâtiment isolé (modèle à l'échelle) à l'aide d'un exemple de l'AIJ (Architectural Institute of Japan). The chosen results (velocity magnitude) are compared with the measured values.
Cet exemple de vérification compare le calcul des charges de vent sur un bâtiment avec une toiture à deux versants selon la norme ASCE 7-16 et celui de la simulation CFD dans RWIND Simulation. The building is defined according to the sketch and the inflow velocity profile taken from the ASCE 7-16 standard.
Cet exemple de vérification compare le calcul des charges de vent sur une toiture terrasse selon la norme ASCE 7-16 et celui de la simulation CFD dans RWIND Simulation. The building is defined according to the sketch and the inflow velocity profile taken from the ASCE 7-16 standard.
L'exemple de vérification compare le calcul de la charge de vent sur un bâtiment avec une toiture à deux versants à l'aide de la norme EN 1991-1-4 et de la simulation CFD dans RWIND Simulation. The building is defined according to the sketch, and the inflow velocity profile is taken according to the standard EN 1991-1-4.
The verification example compares wind load calculation on a building with a flat roof using the standard EN 1991-1-4 and using CFD simulation in RWIND Simulation. Le bâtiment est défini d'après le croquis et le profil de vitesse d'afflux est calculé selon la norme EN 1991-1-4.
Un système à un degré de liberté avec un jeu et deux ressorts est initialement fléchie. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
Une membrane est tendue au moyen d'une précontrainte isotrope entre deux rayons de deux cylindres concentriques ne se trouvant pas dans un plan parallèle à l'axe vertical. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Cet exemple de vérification est basé sur l'exemple de vérification 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
A symmetrical shallow structure is made of eight equal truss members, which are embedded into hinge supports. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. Le poids propre est négligé dans cet exemple. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
A structure is made of four truss members, which are embedded into hinge supports. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. Le poids propre est négligé dans cet exemple. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Une plaque orthotrope rectangulaire mince est simplement supportée et chargée par une pression uniformément répartie. The directions of axes x and y coincide with the principal directions. While neglecting self-weight, determine the maximum deflection of the plate.
Un système à un degré de liberté avec un amortisseur est soumis à une force de charge constante. Determine the deflection and velocity of the dashpot endpoint in the given test time.
Une structure de toiture en coque est modélisée là où les bords droits sont libres, tandis que les translations y et z sont contraintes sur les bords courbes. Neglecting self‑weight, compute the maximum (absolute) vertical deflection, and compare the results with COMSOL Multiphysics 4.3.
Un oscillateur simple est composé de la masse m (considérée uniquement dans la direction x) et du ressort linéaire de rigidité k. The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
Une structure à travée simple sur deux niveaux est soumise à des charges sismiques. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
Une barre de section carrée est fixée à l'extrémité supérieure. The rod is loaded by self-weight. For comparison, the example is also modeled with the concentrated force load, the value of which is equal to the gravity. The aim of this verification example is to show the difference between these types of loading, although the total loading force is equal.
Un mur en maçonnerie est exposé à une charge répartie au centre de sa partie supérieure. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Considérez un tube d'échafaudage rigide, fixé en bas à l'aide de l'appui nodal d'échafaudage et chargé à la fois par un moment et une force. Calculate the maximum deflection with consideration of initial slippage.
Considérez un tube d'échafaudage rigide, fixé en bas à l'aide de l'appui nodal d'échafaudage et chargé à la fois par un moment et une force. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Analyse de l'historique de temps d'une poutre en porte-à-faux (système SDOF) activée par une fonction périodique. Vertical deformations and accelerations calculated with direct integration and modal analysis in RF‑/DYNAM Pro - Forced Vibrations are compared with the analytical solution.
Une poutre en bois renforcée par deux plaques en acier aux extrémités est chargée en pression. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Quatre poteaux sont encastrés en bas et reliés par un bloc rigide en haut. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
A vertical cantilever with a square cross-section is loaded at the top by tensile pressure. Le porte-à-faux est en matériau isotrope. Calculate the deflection.
Déterminez le moment fléchissant qui, agissant à l'extrémité libre du porte-à-faux, fléchit la barre en forme circulaire. Neglecting the beam's self-weight, assuming the large deformation analysis, and loading the cantilever with the moment, determine its maximum deflections.
Une poutre est entièrement encastrée (gauchissement limité) à l'extrémité gauche et supportée par un appui à fourche (gauchissement activé) à l'extrémité droite. The beam is subjected to a torque, longitudinal force, and transverse force. Determine the behavior of the primary torsional moment, secondary torsional moment, and warping moment. The verification example is based on the example introduced by Gensichen and Lumpe.
Un porte-à-faux profilé en I est supporté à l'extrémité gauche et chargé par un couple. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. le poids propre est négligé. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.