Una struttura costituita da un profilo a I è incorporata nei supporti delle forche. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
Una struttura poco profonda simmetrica è composta da otto aste reticolari uguali, che sono incorporate nei supporti delle cerniere. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
Una struttura è composta da quattro aste reticolari, che sono incastonate nei vincoli esterni delle cerniere. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Una struttura reticolare è costituita da tre aste (una in acciaio e due in rame) unite da un'asta rigida. The structure is loaded by a concentrated force and a temperature difference. While neglecting self‑weight, determine the total deflection of the structure.
Uno sbalzo di sezione trasversale rettangolare ha una massa alla fine. Furthermore, it is loaded by an axial force. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Una struttura intelaiata a due piani a campata singola è soggetta a carichi sismici. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
Questo esempio serve come dimostrazione del vincolo del diaframma. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
A structure is made of two trusses of unequal length, which are embedded into the hinge supports. The structure is loaded by concentrated force. Il peso proprio è trascurato. Determine the relationship between the loading force and the deflection, considering large deformations.
Una struttura composta da un profilo a I è completamente fissata all'estremità sinistra e incorporata nel supporto scorrevole all'estremità destra. The structure consists of two segments. The self-weight is neglected in this example. Determine the maximum deflection of the structure, the bending moment on the fixed end, the rotation of segment 2, and the reaction force at point B by means of the geometrically linear analysis and the second-order analysis. The verification example is based on the example introduced by Gensichen and Lumpe.
Quattro colonne sono fissate nella parte inferiore e collegate da un blocco rigido nella parte superiore. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Una fune di acciaio o una membrana con perni su entrambe le estremità è caricata da un carico distribuito. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
A structure is made of two trusses, which are embedded into the hinge supports. The structure is loaded by concentrated force. Il peso proprio è trascurato. Determine the relationship between the loading force and the deflection, considering large deformations.
Una struttura composta da travi reticolari con profilo a I è supportata su entrambe le estremità da vincoli di scorrimento a molla e caricata da forze trasversali. The self-weight is neglected in this example. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
Uno sbalzo in acciaio con una sezione trasversale rettangolare è completamente fissato su un lato e libero sull'altro. The aim of this verification example is to determine the natural frequencies of the structure.
Una struttura reticolare planare è semplicemente vincolata. The aim of this verification example is to determine the natural frequencies of the structure.