Un porte-à-faux de profilé en I est supporté à l'extrémité gauche et est chargé par le moment de rotation M. Le but de cet exemple est de comparer l'appui encastré avec l'appui latéral et torsionnel et d'analyser le comportement de certaines valeurs représentatives. La comparaison avec la solution à l'aide de plaques est également effectuée. L'exemple de vérification est basé sur l'exemple introduit par Gensichen et Lumpe.
Une bielle de section circulaire est supportée selon quatre cas de base de flambement selon Euler et est soumise à une force de pression. Determine the critical load.
Une plaque orthotrope rectangulaire mince est simplement supportée et chargée par une pression uniformément répartie. The directions of axes x and y coincide with the principal directions. While neglecting self-weight, determine the maximum deflection of the plate.
Une structure en profilé en I est entièrement encastrée à l'extrémité gauche et intégrée dans un support glissant à l'extrémité droite. La structure est composée de deux segments. Le poids propre est négligé dans cet exemple. Déterminer la flèche maximale de la structure uz,max, le moment fléchissant My sur l'extrémité fixe, la rotation &svarphi;2,y du segment 2 et la force de réaction RBz à l'aide de l'analyse géométriquement linéaire et de l'analyse du second ordre. L'exemple de vérification est basé sur l'exemple introduit par Gensichen et Lumpe.
Une poutre est entièrement encastrée (gauchissement limité) à l'extrémité gauche et supportée par un appui à fourche (gauchissement libre) à l'extrémité droite. La poutre est soumise à un moment de torsion, une force longitudinale et une force transversale. Déterminer le comportement du moment de torsion primaire, du moment de torsion secondaire et du moment de gauchissement. L'exemple de vérification est basé sur l'exemple introduit par Gensichen et Lumpe (voir la référence).
Un oscillateur simple est composé de la masse m (considérée uniquement dans la direction x) et du ressort linéaire de rigidité k. The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
Une plaque triangulaire équilatérale simplement supportée est soumise à une charge transversale uniformément répartie. Assuming the small deformation theory and neglecting self‑weight, the maximum out‑of‑plane deflection of the plate is determined.
À l'aide des tableaux du manuel AISC, déterminez les résistances en compression et en flexion disponibles et si la poutre ASTM A992 W14x99 présente une résistance suffisante pour supporter les efforts normaux et les moments indiqués dans la Figure 1, obtenue à partir d'une analyse du second ordre qui inclut les effets P-𝛖.
Un porte-à-faux profilé en I est supporté à l'extrémité gauche et chargé par un couple. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).
Une force concentrée est appliquée pendant une courte période de temps au centre de la travée d’une poutre sur appui simple. Considering only the small deformation theory and assuming that the mass of the beam is concentrated at its mid‑span, determine its maximum deflection.
Cet exemple sert de démonstration du couplage de diaphragme. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
La rotation axiale du profilé en I est limitée aux deux extrémités à l'aide des appuis à fourche (le gauchissement n'est pas limité). La structure est chargée par deux forces transversales en son centre. Le poids propre est négligé dans cet exemple. Déterminer les flèches maximales de la structure uy,max et uz,max, la rotation maximale φx,max, les moments fléchissants maximaux My,max et Mz,max et les moments de torsion maximaux MT,max, MTpri,max MTsec,max et Mω,max. L'exemple de vérification est basé sur l'exemple introduit par Gensichen et Lumpe.
Une poutre est entièrement encastrée (gauchissement limité) à l'extrémité gauche et supportée par un appui à fourche (gauchissement activé) à l'extrémité droite. The beam is subjected to a torque, longitudinal force, and transverse force. Determine the behavior of the primary torsional moment, secondary torsional moment, and warping moment. The verification example is based on the example introduced by Gensichen and Lumpe.
A structure made of an I-profile is fully fixed on the left end and embedded into the sliding support on the right end. The structure consists of two segments. Le poids propre est négligé dans cet exemple. Determine the maximum deflection of the structure, the bending moment on the fixed end, the rotation of segment 2, and the reaction force at point B by means of the geometrically linear analysis and the second-order analysis. The verification example is based on the example introduced by Gensichen and Lumpe.
Une poutre en acier chargée axialement avec une section carrée est fixée à une extrémité et supportée par un ressort à l'autre. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
A structure is made of two trusses, which are embedded into the hinge supports. The structure is loaded by concentrated force. le poids propre est négligé. Determine the relationship between the loading force and the deflection, considering large deformations.
Une structure constituée de treillis profilés en I est soutenue aux deux extrémités par des appuis à ressort et chargée par les efforts transversaux. Le poids propre est négligé dans cet exemple . Déterminez la flèche de la structure, le moment fléchissant, l'effort normal dans des points d'essai donnés et la flèche horizontale de l'appui du ressort.
A structure made of I-profile trusses is supported on both ends by spring sliding supports and loaded by transversal forces. Le poids propre est négligé dans cet exemple. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.