本例题中的钢筋混凝土梁为两跨悬臂梁。 截面沿悬臂长度方向不断变化(变截面)。 计算最终极限状态下的内力以及所需的纵向和剪切钢筋。
在本例中,不同时间浇筑的混凝土与相应钢筋之间界面的剪力按照 DIN EN 1992-1-1 确定。 下面将使用 RFEM 6 获得的结果与手算结果进行比较。
EN 1991-1-4 [1]、ASCE/SEI 7-16 和 NBC 2015 等现有标准给出了风荷载参数,例如风压系数 (Cp )基本形状。 重要的是如何更快,更准确地计算风荷载参数,而不是使用标准中的耗时且有时复杂的公式。
在当前的验证示例中,我们按照 EN 1991-1-4 [1] 研究了立方体形状的风力系数 (Cf )。 如果是三维情况,我们将在下一部分中详细介绍。
该模型基于 [1] 的示例 4: 点支座楼板。
将设计一栋办公楼的平板,该建筑采用对裂缝敏感的轻质墙体。 内部、边缘和角部板件将被检查。 柱子和平板是整体连接的。 边柱和角柱与板的边缘齐平。 柱的轴线形成一个方形网格。 它是一个刚性体系(用剪力墙加劲的建筑物)。
该办公楼有5层,层高3.000 m。 假设的环境条件定义为“封闭的内部空间”。 主要是静力作用。
本例的重点是确定板在满载情况下的弯矩和柱上方所需的配筋。
一个钢悬臂梁,具有矩形截面,一侧完全固定,另一侧自由。 The aim of this verification example is to determine the natural frequencies of the structure.
左端支承着一个工字形的悬臂梁,给悬臂梁施加扭矩 M。 本例的目的是对固定式支座和货叉式支座进行比较,并研究一些有代表性的问题的行为。 并与通过板的解决方案进行了比较。 验算示例是基于 Gensichen 和 Lumpe 介绍的示例.
在当前的验证示例中,我们按照欧洲规范 EN 1991-1-4 研究了矩形建筑的一般结构设计 (Cp,10 ) 以及幕墙或外墙设计 (Cp,1 ) 的风压值[1]. 如果是三维情况,我们将在下一部分中详细介绍。
从外部施加压力。 Determine the critical load and corresponding load factor for in-plane buckling.
双质量振型由两个线性弹簧和质量点组成,这些弹簧和质量集中在节点处。 The self-weight of the springs is neglected. Determine the natural frequencies of the system.
对该梁施加面外力,其截面为矩形截面。 This force causes a bending moment, torsional moment, and transverse force. While neglecting self-weight, determine the total deflection of the curved beam.
简支梁施加纯弯矩荷载。 Determine the critical load and corresponding load factor due to lateral buckling.
一个球面上有均匀的粘性流体流。 The velocity of the fluid is considered at infinity. The goal is to determine the drag force. The parameters of the problem are set so that the Reynolds number is small and the radius of the sphere is also small, thus the theoretical solution can be reached - Stokes flow (G. G. Stokes 1851).
矩形钢板 实现边缘简支。 Determine the natural frequencies of the rectangular plate.
柱由截面混凝土(矩形100/200)和钢截面(截面 I 200)组成。 It is subjected to pressure force. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
带孔宽板在一个方向上通过拉应力 σ 加载。 考虑到平面应力状态,板宽相对于孔半径很大,并且非常薄。 确定孔周围的径向应力 σr 、切向应力 σθ和剪应力 τrθ 。
一个矩形截面的悬臂梁,采用弹性 Winkler 基础,并施加均布荷载。 The image shows the calculation of the maximum deflection and maximum bending moment.
该模型基于 [1] 的示例 4: 点支座楼板。 内力和所需的纵向配筋参见验证示例 1022。 在本例中,我们在轴 B/2 上检查冲切。
悬臂在其自由端施加一个弯矩。 Using the geometrically linear analysis and large deformation analysis, and neglecting the beam's self-weight, determine the maximum deflections at the free end. The verification example is based on the example introduced by Gensichen and Lumpe.
设计一个三层建筑的内柱。 柱子与上、下梁采用整体连接。 然后与 EC2-1-2 中柱的抗火设计[#Refer [1]]] 进行了验证,结果与 [1] 进行了比较。
使用 RFEM 计算了湖相黏土上刚性方形地基[1]的沉降。 已对四分之一的基础进行建模。 基础两侧的宽度为 75.0 m。 施工阶段用于生成结果。