19 Wyniki
Wyświetl wyniki:
Sortuj według:
- 005599
- RFEM 6
- Projektowanie konstrukcji betonowych RFEM 6
-
- Projektowanie konstrukcji betonowych RSTAB 9
- RSTAB 9
- Projektowanie konstrukcji drewnianych RFEM 6
- Projektowanie konstrukcji drewnianych RSTAB 9
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Analiza etapów budowy (CSA) dla RFEM 6
- Konstrukcje betonowe
- Konstrukcje stalowe
- Konstrukcje drewniane
- Analiza statyczno-wytrzymałościowa
konfiguracje obliczeniowe mogą się różnić w zależności od przypadku
Jak przeprowadzić wymiarowanie prętów dla różnych ustawień w konfiguracji obliczeniowej?
Wymiary w połączeniu stalowym
Czy mogę dodać wymiary w rozszerzeniu Połączenia stalowe?
Usztywnienia na pasach dźwigarów w połączeniu z ramą sztywną
W jaki sposób usztywnienia na zewnętrznych krawędziach pasów belki połączenia sztywnego ramy wpływają na maksymalny przenoszony moment oraz na sztywność obrotową i powiązane przemieszczenia konstrukcji ramy?
Metoda elementów skończonych oparta na komponentach (CBFEM) w RFEM 6
Co to jest metoda elementów skończonych oparta na komponentach (CBFEM)?
Cięcie i edycja płyt
Dlaczego w komponentach „Cięcie płyty” i „Edytor arkusza” nie można wybrać płyty, którą chcę dostosować?
- 005437
- RFEM 6
- RSTAB 9
-
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Połączenia stalowe RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RFEM 6
- Skręcanie skrępowane (7 stopni swobody) RSTAB 9
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Analiza naprężeń
- Sprawdzenie stateczności
- Analiza skręcania skrępowanego
- Połączenia stalowe
- Profile formowane na zimno
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263
Programy dla konstrukcji stalowych
Jakie programy i rozszerzenia są odpowiednie do obliczeń i wymiarowania konstrukcji stalowych?
Połączenie nakładkowe
Jak utworzyć połączenie typu splot w rozszerzeniu Steel Joints?
AISC 360-16 Płaszczyzna ścinania w gwincie
Czy mogę wykluczyć gwinty śrub z płaszczyzn ścinania zgodnie z AISC 360-16 w rozszerzeniu Połączenia stalowe?
Kierunek ortotropowy dla warstw
Dlaczego'nie mogę zdefiniować obrotu podczas definiowania warstw?
Wymiarowanie w oparciu o przypadek z różnymi sytuacjami obciążenia
Jak przeprowadzić obliczenia w zależności od przypadku dla różnych sytuacji obciążeniowych?
Nieprawdopodobne wyniki skręcania skrępowanego
Moje wyniki dla obliczeń ze skręcaniem skrępowanym są nieprawdopodobne. Jaka może być tego przyczyna?
Sprężyna deplanacyjna i naprężenia deplanacyjne
Jak mogę zdefiniować sprężystość deplanacyjną lub naprężenie deplanacyjne?
Podpory i obciążenia do obliczeń ze względu na skręcanie skrępowane
W którym punkcie przekroju są przyjmowane podpory i obciążenia ze względu na skręcanie skrępowane do obliczeń?
Faza budowy - modyfikacja właściwości
Czy na poszczególnych etapach budowy można zmieniać właściwości prętów lub powierzchni, np. ich położenie?
- 005113
- Projektowanie konstrukcji drewnianych RFEM 6
- Projektowanie konstrukcji drewnianych RSTAB 9
-
- Projektowanie konstrukcji aluminiowych RFEM 6
- Projektowanie konstrukcji aluminiowych RSTAB 9
- Projektowanie konstrukcji stalowych RFEM 6
- Projektowanie konstrukcji stalowych RSTAB 9
- Analiza naprężeniowo-odkształceniowa RFEM 6
- Analiza naprężeniowo-odkształceniowa RSTAB 9
- Połączenia stalowe RFEM 6
- Konstrukcje drewniane
- Konstrukcje betonowe
- Konstrukcje stalowe
- Analiza statyczno-wytrzymałościowa
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9