Bas Boellaard
Solid Timber
The Netherlandswww.solidtimber.nl
So Beneficial
Have been using the add-on module RF-/JOINTS Timber - Steel to Timber and it's for sure very straight forward and easy to use. The thing is that integrating the joint stiffness into a model is something which is so beneficial. That's the way one would like it to work.
Do you have any questions?
Length: 00:00:37 min
Length: 00:03:27 min
Length: 00:00:56 min
Product Feature
Length: 00:01:06 min
Length: 00:00:00 min
Length: 00:55:27 min
Length: 00:50:35 min
Length: 01:10:03 min
Using the Timber Design add-on, timber column design is possible according to the 2018 NDS standard ASD method. Accurately calculating timber member compressive capacity and adjustment factors is important for safety considerations and design. The following article will verify the maximum critical buckling strength calculated by the Timber Design add-on using step-by-step analytical equations as per the NDS 2018 standard including the compressive adjustment factors, adjusted compressive design value, and final design ratio.
The Geotechnical Analysis add-on provides RFEM with additional specific soil material models that are able to suitably represent complex soil material behavior. This technical article is an introduction to show how the stress-dependent stiffness of soil material models can be determined.
This article shows how to create cross-sections using DXF files.
When calculating regular structures, data input is often not complicated but time-consuming. Input automation can save valuable time. The task described in the present article is to consider the stories of a house as single construction stages. Data is entered using a C# program so that the user does not have to enter the elements of the individual floors manually.
Using the "Beam Panel" thickness type, you can model timber panel elements in 3D space. You just specify the surface geometry and the timber panel elements are generated using an internal member-surface construct, including the simulation of the connection flexibility.
You have the option to perform the fire resistance design of surfaces using the reduced cross-section method. The reduction is applied over the surface thickness. It is possible to perform the design checks for all timber materials allowed for the design.
For cross-laminated timber, depending on the type of adhesive, you can select whether it is possible for individual carbonized layer parts to fall off, and whether you can expect increased charring in certain layer areas.
.png?mw=512&hash=4e74affa9ad0c7b703151c5085ac9b8e59171c23)
Among others, the following cross-laminated timber manufacturers are available in the layer structure library:
- Binderholz (USA)
- KLH (USA, CAN)
- Kalesnikoff (USA, CAN)
- Nordic Structures (USA, CAN)
- Mercer Mass Timber
- SmartLam
- Sterling Structural
- Superstructures listed in Lignatec Edition 32 "Cross-Laminated Timber of Swiss Production"
By importing a structure from the layer structure library, all relevant parameters are adopted automatically. The library is continually updated.
The Timber Design add-on for RFEM 6 / RSTAB 9 is multi-purpose and combines a large number of additional elements. [*S16332764*] Timber Design Add-on for RFEM 6
I would like to design the connection of the diagonals of a truss with a steel lower flange and timber diagonals. Is this possible?
Is it possible to use the JOINTS add-on module to design timber-to-timber connections according to EN 1995‑1‑1, Chapter 8.2.2, in RFEM 5 and RSTAB 8?
How can I generate an area load on members via cells in RFEM 6 or RSTAB 9?
How can I define temporary supports for a form-finding process in RFEM& 6?
Which programs do I need for laminate and sandwich structures, or cross-laminated timber (CLT)?
Which Dlubal Software programs can I use to calculate and design timber structures?
.jpg?mw=350&hash=8f312d6c75a747d88bf9d0f5b1038595900b96c1)