The structural analysis software RFEM 6 is the basis of a modular software system. The main program RFEM 6 is used to define structures, materials, and loads of planar and spatial structural systems consisting of plates, walls, shells, and members. The program also allows you to create combined structures as well as to model solid and contact elements.
RSTAB 9 is a powerful analysis and design software for 3D beam, frame, or truss structure calculations, reflecting the current state of the art and helping structural engineers meet requirements in modern civil engineering.
Do you often spend too long calculating cross-sections? Dlubal Software and the RSECTION stand-alone program facilitate your work by determining section properties of various cross-sections and performing a subsequent stress analysis.
Do you always know where the wind is blowing from? From the direction of innovation, of course! With RWIND 2, you have a program at your side that uses a digital wind tunnel for the numerical simulation of wind flows. The program simulates these flows around any building geometry and determines the wind loads on the surfaces.
Are you looking for an overview of snow load zones, wind zones, and seismic zones? Then you are in the right place. Use the Geo-Zone Tool to determine quickly and efficiently snow loads, wind speeds, and seismic data according to ASCE 7‑16 and other international standards.
Would you like to try out the capabilities of the Dlubal Software programs? You have the opportunity to do so! The free 90-day full version allows you to thoroughly test all our programs.
In this webinar, you will learn how to design stiffening in RFEM 6 using Building Model.
AISC 360-22 Steel Connection Design in RFEM 6 (USA)
This webinar will provide an introduction to steel connection design acc. to the AISC 360-22 in RFEM 6.
In this webinar, we'll show how to address commonly asked questions recently sent to the Dlubal support team in RFEM 6 and RSTAB 9.
This webinar will provide an introduction to steel member design acc. to the AISC 360-22 and 341-22 in RFEM 6.
In this webinar, you get an introduction to the interface RFEM 6 – Tekla Structures.
In this webinar, you will learn how to perform linear stability analyses in RFEM 6 and RSTAB 9.
In this webinar, you will learn about advanced structural analysis with RFEM 6 Python API.
In this webinar, you will learn how to optimize mass distribution for harmonically excited models of supporting structures in RFEM 6.
In this webinar, you will learn how to calculate masonry structures in RFEM 6 using an FE analysis.
In this webinar, you will learn how to calculate connections with circular hollow sections in RFEM 6.
In this webinar, you will learn how to calculate reinforced concrete slabs in RFEM 6.
In this webinar, you will learn how to calculate timber floors in RFEM 6.
Free Webinar | RWIND 2 - Calculating Wind Loads with CFD Simulation (USA)
This webinar will provide an overview of calculating wind loads using CFD simulation with RWIND 2 and RFEM 6.
In this webinar, you will learn how to perform geotechnical analyses in RFEM 6.
In this webinar, you will learn about the new features implemented in our Dlubal Software programs and about new add-ons that have been released.
In this webinar, you will learn how to control the Design add-ons of RFEM 6 by means of templates.
In this free webinar, we show the options in RFEM 6 and RSTAB 9 for modeling and dimensioning solids and welds, calculating stress ranges for fatigue design, and creating documentation.
In this webinar, you will learn how to design a tent hall consisting of aluminum cross-sections in RFEM 6.
Free Webinar | Introduction to Time History Analysis in RFEM 6 (USA)
This webinar will provide an introduction to time history analysis in RFEM 6.
This webinar shows you how to integrate AI to RFEM using API.
In this webinar, you will learn how to perform wind simulations in RWIND 2 and RFEM 6.
In this webinar, we show you some of the new features that have recently been added to the Steel Joints add-on for RFEM 6.
In this free webinar, we show you the questions asked about RFEM 6 and RSTAB 9, which have recently been answered by Dlubal support team.
In this webinar, we show you how to analyze machine-induced vibrations using the Time History Analysis add-on.
In this webinar, we show you how to perform seismic designs for reinforced concrete structures in RFEM 6.
In this webinar, we show you how to consider various construction stages in the RFEM 6 structural analysis program.