Webinars – Learn Online - Norme: ASCE 7

AISC 360-22 Steel Connection Design in RFEM 6 (USA)

This webinar will provide an introduction to steel connection design acc. to the AISC 360-22 in RFEM 6.

This webinar will provide an introduction to steel member design acc. to the AISC 360-22 and 341-22 in RFEM 6.

Free Webinar | RWIND 2 - Calculating Wind Loads with CFD Simulation (USA)

This webinar will provide an overview of calculating wind loads using CFD simulation with RWIND 2 and RFEM 6.

Free Webinar | AISI S100 / CSA S136 Cold-Formed Steel Design in RFEM 6 (USA)

This webinar will provide an introduction to cold-formed steel member design acc. to the AISI S100 / CSA S136 in RFEM 6.

Free Webinar | AISC 360-16 Steel Connection Design in RFEM 6 (USA)

This webinar will provide an introduction to steel connection design using FEA acc. to the AISC 360-16 in RFEM 6.

Free Webinar | 2018 NDS CLT Design in RFEM 6 (USA)

This webinar will provide an introduction to cross-laminated timber (CLT) design acc. to the 2018 NDS in RFEM 6.

Free Webinar | Steel Silo Design in RFEM 6 (USA)

This webinar will provide an introduction to steel silo design in RFEM 6.

Free Webinar | Reinforced Concrete Tank Design in RFEM 6 (USA)

This webinar will provide an introduction to reinforced concrete tank analysis and design in RFEM 6.

Free Webinar | Construction Stages Analysis in RFEM 6 (USA)

This webinar will provide an introduction to construction stage analysis and design in RFEM 6.

Free Webinar | CFD Wind Simulation with RWIND 2 (USA)

This webinar will provide an introduction to CFD wind analysis utilizing RWIND 2 and RFEM 6.

Free Webinar | ADM 2020 Aluminum Design in RFEM 6 (USA)

This webinar will provide an introduction to aluminum member design acc. to the ADM 2020 in RFEM 6.

Free Webinar | ASCE 7-16 Response Spectrum Analysis in RFEM 6 (USA)

This webinar will provide an introduction to a response spectrum analysis acc. to the ASCE 7-16 in RFEM 6.

Free Webinar | Tensile Membrane Structure Design in RFEM 6 (USA)

This webinar will provide an introduction to tensile membrane structure design in RFEM 6.

Free Webinar | NDS 2018 Timber Member Design in RFEM 6 (USA)

This webinar will provide an introduction to timber member design acc. to the NDS 2018 in RFEM 6.

Free Webinar | AISC 360-16 Steel Design in RFEM 6 (USA)

This webinar will provide an introduction to steel design acc. to the AISC 360-16 in RFEM 6.

This webinar will provide an introduction to the new generation FEA software RFEM 6.

Webinars provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.

This webinar demonstrates the aluminum member design workflow according to the Aluminum Design Manual (ADM) 2020 in RFEM.

Webinars provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.

This webinar demonstrates the general workflow for tensile membrane structure design in RFEM including CFD wind load analysis utilizing RWIND Simulation.

Webinars provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.

Content:

• Buckling behavior of members utilizing RF‑STABILITY
• Use of “line releases” for beam to surface connection
• Addressing FEA singularities with concrete surface design
• Nonlinear material modeling with a plastic stress analysis of a steel connection

Content:

• Overview and features of RFEM and the design add‑on modules
• Modeling, loading, and analysis of a multi‑material structure in RFEM
• Introduction to the design add-on modules RF-STEEL AISC and RF-CONCRETE 
• Review of result output and printout report

Contents

• Concept of RFEM and RF-GLASS
• Simplified connections of point-supported glass with nodal supports
• Detailed connections of point-supported glass with contact solids

Content:

• Introduction to the RF‑DYNAM Pro add‑on modules
• Natural frequencies and mode shapes calculation
• Response spectrum analysis per ASCE 7-16
• Story drift, story shear, and P-Delta considerations

Content

• Modeling, loading (ASCE 7-16), and analysis of a timber arch structure in RFEM
• Member design (NDS-2018) in RF-TIMBER AWC
• Consideration of curved glulam design
• Program printout report options available

Content

• IFC building import in RFEM for geometry guidelines
• Tensile membrane design in RF-FORM-FINDING and RF-CUTTING-PATTERNS
• Design of supporting structure in RF-STEEL AISC
• Results export to AutoCAD and REVIT

Content

• Concept of RFEM and RF-GLASS
• Simplified glass point supported fittings with nodal supports
• Detailed glass point supported fittings with contact solids

• Direct integration link between Revit and RFEM
• Explore various scenarios of Revit to RFEM import/export
• Round-tripping of updated model between programs
• Useful tips for a more optimized integration

Content

• Overview of updates to RF-STEEL AISC.
• Steel member design per AISC 360-16.
• New add-on module RF-STEEL Warping Torsion.
• Steel warping torsion design per AISC Design Guide 9.

Content

• Overview of 2018 NDS updates with CLT design.
• Modeling and loading of a CLT structure in RFEM.
• Analysis and design per 2018 NDS utilizing RF-LAMINATE.

Content

• Column and rib member design in RF-CONCRETE Members.
• Spandrel design above wall openings (result beams) in RF-CONCRETE Members.
• Wall design in RF-CONCRETE Surfaces.
• Addressing singularities in FEA concrete design.

Content

• Overview of dynamic analysis in RFEM and the Dynam Pro add-on modules.
• Natural frequency analysis of a structure using RF-DYNAM Pro - Natural Vibrations.
• Linear time history analysis with machine induced vibrations using RF-DYNAM Pro - Forced Vibrations.
• Nonlinear time history analysis using RF-DYNAM Pro - Nonlinear Time History.