After starting the module, the joint group (rigid joints) is selected first, followed by joint category and joint type (rigid end plate connection or rigid splice plate connection). The nodes to be designed are then selected from the RFEM/RSTAB model. RF-/JOINTS Steel - Rigid automatically recognizes the joint members and determines from its location whether they are columns or beams. The user can intervene here.
If certain members are to be excluded from the calculation, they can be deactivated. Structurally similar connections can be designed for several nodes at the same time. Loads require selection of the governing load cases, load combinations, or result combinations. Alternatively, you can enter the cross‑section and load data manually. In the last input window, the connection is configured step by step.
Beam to Column joint category: connection possible as joint of the beam to the column flange as well as joint of the column to the girder flange
Beam to Beam joint category: design of beam joints as both moment-resisting end plate connections and rigid splice connections possible
Automatic export of model and load data possible from RFEM or RSTAB
Bolt sizes from M12 to M36 with strength grades 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, and 10.9 as long as the strength grades are available in the selected National Annex
Almost any bolt spacing and edge distances (a check of the allowable distances is performed)
Beam strengthening with tapers or stiffeners on the top and bottom surfaces
End plate connection with and without overlap
Connection with pure bending stress, pure normal force load (tension joint), or combination of normal force and bending possible
Calculation of connection stiffnesses and check if a hinged, semi-rigid, or rigid connection exists
End plate connection in a beam-column setup
Joint beams or columns can be stiffened with tapers on one side or with stiffeners to one or both sides
Wide range of possible stiffeners of the connection (for example, complete or incomplete web stiffeners)
Up to ten horizontal and four vertical bolts possible
Connected object possible as constant or tapered I-section
Designs:
Ultimate limit state of the connected beam (such as shear or tension resistance of the web plate)
Ultimate limit state of the end plate at the beam (for example, T-stub under tensile stress)
Ultimate limit state of the welds at the end plate
Ultimate limit state of the column in the area of the connection (for example, column flange under bending – T-stub)
All designs are performed according to EN 1993-1-8 and EN 1993-1-1
Moment-resisting end plate joint
Two or four vertical and up to 10 horizontal bolt rows
Joint beams can be stiffened with tapers on one side or with stiffeners to one or both sides
Connected objects are possible as constant or tapered I-sections
Designs:
Ultimate limit state of the connected beams (such as shear or tension resistance of the web plates)
Ultimate limit state of the end plates at the beam (for example, T-stub under tensile stress)
Ultimate limit state of the welds at the end plates
Ultimate limit state of the bolts in the end plate (combination of tension and shear)
Rigid splice plate connection
For the flange plate connection, up to ten bolt rows one behind the other possible
For the web plate connection, up to ten bolt rows possible each in vertical and horizontal directions
Material of the cleat can be different from the one of the beams
Designs:
Ultimate limit state of the joint beams (for example, net cross-section in the tension area)
Ultimate limit state of the cleat plates (for example, net cross-section under tensile stress)
Ultimate limit state of the single bolts and the bolt groups (for example, shear resistance design of the single bolt)
Design of moment resistant and simple joints of I-shaped rolled cross-sections according to Eurocode 3:
Moment-resisting end plate connections (type IH/IM)
Moment resistant purlin splices (PM type)
Simple joints with angle cleat and long angles (IW and IG types)
Simple joints with header end plates mounted either on web only or on web and flange (IS type)
Check of coped connections (IK) in combination with pinned end plates (IS) and angle connections (IW)
Automatic design of required joint with bolt sizes (all types)
Check of required thickness of load-bearing members for shear connections
Results of all required structural details such as appliances, hole arrangements, necessary extensions, a number of bolts, end plate dimensions, and welds
Results including stiffnesses Sj,ini of bending-resistant connections
Documentation of available loading and comparison with resistances
Results of design ratio for each individual joint
Automatic determination of governing internal forces for several load cases and connection nodes
Geometry, material, cross-section, action, and imperfection data are entered in clearly arranged input windows:
Geometry
Quick and convenient data input
Definition of support conditions based on various support types (hinged, hinged movable, rigid, and user-defined, as well as lateral on upper or bottom flange)
Optional specification of warping restraint
Variable arrangement of rigid and deformable support stiffeners
Possibility to insert hinges
CRANEWAY Cross-Sections
I-shaped rolled cross-sections (I, IPE, IPEa, IPEo, IPEv, HE-B, HE-A, HE-AA, HL, HE-M, HE, HD, HP, IPB-S, IPB-SB, W, UB, UC, and other cross-sections according to AISC, ARBED, British Steel, Gost, TU, JIS, YB, GB, and others) combinable with section stiffener on the upper flange (angles or channels) as well as rail (SA, SF) or splice with user-defined dimensions
Unsymmetrical I-sections (type IU) also combinable with stiffeners on the upper flange as well as with rail or splice
Actions
It is possible to consider the actions of up to three simultaneously operated cranes. You can simply select a standard crane from the library. You can also enter data manually:
Number of cranes and crane axles (maximum of 20 axles per crane), center distances, position of crane buffers
Classification in damage classes with editable dynamic factors according to EN 1993-6, and in lifting classes and exposure categories according to DIN 4132
Vertical and horizontal wheel loads from self-weight, hoist load, mass forces from drive, as well as loads from skewing
Axial loading in driving direction as well as buffer forces with user-defined eccentricities
Permanent and variable secondary loads with user-defined eccentricities
Imperfections
The imperfection load applies in compliance with the first natural vibration mode - either identically for all load combinations to be designed, or individually for each load combination, as mode shapes may vary depending on the load.
Convenient tools available for scaling the mode shapes (rise determination of inclination and precamber).