Membrana jest rozciągana za pomocą wstępnego naprężenia izotropowego między dwoma promieniami dwóch koncentrycznych walców, nie leżących w płaszczyźnie równoległej do osi pionowej. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. The add-on module RF-FORM-FINDING is used for this purpose. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Rozważ belkę ASTM A992 W 18×50 dla stałych i równomiernych obciążeń stałych i ruchomych, jak pokazano na Rysunku 1. The member is limited to a maximum nominal depth of 18 inches. The live load deflection is limited to L/360. The beam is simply supported and continuously braced. Verify the available flexural strength of the selected beam, based on LRFD and ASD.
Belka zakrzywiona składa się z dwóch belek o prostokątnym przekroju. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
Prosty oscylator składa się z masy m (rozpatrywanej tylko w kierunku x) i liniowej sprężystości sztywności k. The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
Ściana murowana jest poddana rozłożonemu obciążeniu w środku swojego górnego przekroju. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Rozważmy sztywną rurę rusztowania, zamocowaną u dołu za pomocą podpory węzłowej rusztowania i obciążoną zarówno momentem, jak i siłą. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Długa, cienka belka przenosi masę skupioną i jest obciążona siłą zależną od czasu. It is simply supported. The problem is described using the following parameters. Determine the deflections in the given test times.
Drewniana belka wzmocniona dwiema stalowymi płytami na końcach jest obciążona ściskaniem. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Konstrukcja wykonana z kratownic o przekroju dwuteowym jest podparta na obu końcach za pomocą sprężynowych podpór przesuwnych i obciążona siłami poprzecznymi. The self-weight is neglected in this example. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
Wspornik o profilu dwuteowym jest podparty na lewym końcu i obciążony momentem obrotowym. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).
Na obu końcach zamocowany jest trójwymiarowy blok wykonany z materiału sprężysto-plastycznego. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Określ maksymalne ugięcie bloku trójwymiarowego zamocowanego na obu końcach. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. The block's middle plane is subjected to vertical pressure.
Drewniana belka wzmocniona dwiema stalowymi płytami na końcach jest obciążona ściskaniem. The wood fibers are parallel to the upper loaded side of the beam. The plastic surface is described according to the Tsai-Wu plasticity theory.
Na obu końcach zamocowany jest trójwymiarowy blok wykonany z materiału sprężysto-plastycznego, który jest utwardzany. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.