Konstrukcja składa się z belki o przekroju dwuteowym i dwóch kratownic rurowych. The structure contains several imperfections and it is loaded by the force Fz. Ciężar własny jest pomijany w tym przykładzie. Determine the deflections uy and uz and axial rotation φx at the endpoint (Point 4). Przykład obliczeniowy oparty jest na przykładzie wprowadzonym przez Gensichen i Lumpe.
Poniższy przykład obliczeniowy jest oparty na przykładzie obliczeniowym 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Symetryczna płytka konstrukcja składa się z ośmiu równych prętów kratownicowych, osadzonych w podporach przegubowych. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point when the snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at the given deflections.
Rura o przekroju rurowym jest obciążona ciśnieniem wewnętrznym. This internal pressure causes axial deformation of the pipe (the Bourdon effect). Determine the axial deformation of the pipe endpoint.
Konstrukcja składa się z czterech prętów kratownicowych, osadzonych w podporach przegubowych. The structure is loaded by a concentrated force and alternatively by imposed nodal deformation over the critical limit point, when snap-through occurs. Imposed nodal deformation is used in RFEM 5 and RSTAB 8 to obtain the full equilibrium path of the snap-through. The self-weight is neglected in this example. Determine the relationship between the actual loading force and the deflection, considering large deformation analysis. Evaluate the load factor at given deflections.
Pomiędzy dwiema podporami podwieszony jest bardzo sztywny kabel. Determine the equilibrium shape of the cable (the catenary), consider the gravitational acceleration, and neglect the stiffness of the cable. Verify the position of the cable at the given test points.
Układ jednomasowy z kotłem typu 'dashpot' jest poddawany stałemu obciążeniu. Determine the deflection and velocity of the dashpot endpoint in the given test time.
Celem tego przykładu jest pokazanie nieodwracalnego procesu spowodowanego tarciem. After the loading and unloading, the end-point is in a different position than where it was at the beginning. Determine the movement of the node in the X direction.
Konstrukcja z profilu I jest w pełni utwierdzona na lewym końcu i osadzona w podporze przesuwnej na prawym końcu. The structure consists of two segments. The self-weight is neglected in this example. Determine the maximum deflection of the structure, the bending moment on the fixed end, the rotation of segment 2, and the reaction force at point B by means of the geometrically linear analysis and the second-order analysis. The verification example is based on the example introduced by Gensichen and Lumpe.
Konstrukcja wykonana z kratownic o przekroju dwuteowym jest podparta na obu końcach za pomocą sprężynowych podpór przesuwnych i obciążona siłami poprzecznymi. The self-weight is neglected in this example. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
Wspornik o profilu dwuteowym jest podparty na lewym końcu i obciążony momentem obrotowym. The aim of this example is to compare the fixed support with the fork support and to investigate the behavior of some representative quantities. Comparison is also made to the solution by means of plates. Small deformations are considered, and the self-weight is neglected. Determine the rotation in the midpoint of the cantilever, and in case of the member entity with warping, determine the values of the primary torsional moment, the secondary torsional moment, and the warping moment both on the left end (point A) and the right end (point B).
Zostanie zdefiniowana belka wspornikowa o przekroju dwuteowym o długości L. The beam has five mass points with masses m acting in the X-direction. The self-weight is neglected. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.