Analyticky stanovíme torzní konstantu pro průřez trubky (kruhovou oblast) a výsledky porovnáme s numerickým řešením v programech RFEM 5 a RSTAB 8 pro různé tloušťky stěn.
Konzola obdélníkového průřezu leží na pružném Winklerově podloží a je zatížena rovnoměrným zatížením. The image shows the calculation of the maximum deflection and maximum bending moment.
Ocelový nosník se čtvercovým průřezem je zatížen normálovou silou a spojitým zatížením. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Osově zatížený ocelový nosník se čtvercovým průřezem je na jednom konci kloubově uložený a na druhém pružně podepřený. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
Jednovrstvá čtvercová ortotropní deska je ve svém středu zcela fixována a namáhána tlakem. Compare the deflections of the plate corners to check the correctness of the transformation.
Na obou koncích je upevněn trojrozměrný blok z elasticko-plastického materiálu. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Determine the maximum deflection of a three-dimensional block fixed at both ends. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. Na rovinu procházející středem bloku působí svislý tlak.
Stanovíme maximální průhyb čtyř dolních sloupů spojených tuhým blokem nahoře. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Plastická plocha je popsána podle teorie plasticity Tsai-Wu.
Na obou koncích je upevněn trojrozměrný blok z elasticko-plastického materiálu s vytvrzením. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
Konzola je plně fixována na levém konci a zatížena příčnou silou a normálovou silou na pravém konci. The tensile strength is zero and the behavior in the compression remains elastic.
Stanovte maximální průhyby bloku se zohledněním nebo zanedbáním smykového účinku. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Stanoví se maximální průhyb a napětí ve směru z spřažené desky, která se skládá ze dvou skleněných vrstev a jedné vrstvy fólie mezi nimi a je vystavena konstantnímu tlaku.
Široká deska s otvorem je zatížena v jednom směru tahovým napětím. The plate width is large with respect to the hole radius, and it is very thin, considering the state of the plane stress.
Dokažte, že spojení různých rozměrových prvků nemá vliv na výsledky. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Plastická plocha je popsána podle teorie plasticity Tsai-Wu.
Ve spodní části jsou upevněny čtyři sloupy, které jsou nahoře spojeny tuhým blokem. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.