Konstrukce se skládá z I-profilu a dvou trubkových nosníků. The structure contains several imperfections and it is loaded by the force Fz. Vlastní tíha se v tomto příkladu nezohledňuje. Determine the deflections uy and uz and axial rotation φx at the endpoint (Point 4). Verifikační příklad vychází z příkladu, který představili Gensichen a Lumpe.
Tento verifikační příklad vychází z verifikačního příkladu 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum deflection with consideration of initial slippage.
Verifikační příklad popisuje zatížení větrem v několika směrech proudění větru na modelu skupiny budov. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Stanoví se maximální průhyb a maximální radiální moment prosté kruhové desky namáhané konstantním tlakem, konstantní teplotou a rozdílem teplot.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. Je prostě podepřený. The problem is described using the following parameters. Determine the deflections in the given test times.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Jednovrstvá čtvercová ortotropní deska je ve svém středu zcela fixována a namáhána tlakem. Porovnejte průhyby rohů desek pro kontrolu správnosti transformace.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Ocelový nosník se čtvercovým průřezem je zatížen normálovou silou a spojitým zatížením. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Hmotový systém s vůlí a dvěma pružinami se nejdříve vychýlí. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
Konzola z kruhového prutu je zatížena excentrickým rovnoměrným zatížením. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
Ocelové lano nebo membrána s kolíky na obou koncích jsou zatíženy rovnoměrným zatížením. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
Silnostěnná nádoba je zatížena vnitřním tlakem tak, že nádoba dosáhne pružno-plastického stavu. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
Jednohmotový systém je vystaven zatěžující síle. Determine the deflection of the system.
Na obrázku 1 je znázorněn nosník ASTM A992 W 24×62 se smykem na konci 48 000 a 145 000 kips od vlastní tíhy a užitného zatížení. Verify the available shear strength of the selected beam, based on LRFD and ASD.
A cantilever of rectangular cross‑section has a mass at the end. Kromě toho je zatížena normálovou silou. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Stanovíme maximální průhyb krychle. The cube's lower side is fully fixed and the upper side is subjected to shear loading.
Stanovte maximální průhyby bloku se zohledněním nebo zanedbáním smykového účinku. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
Tlumený jednohmotový systém je zatížen konstantní silou. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.