Tento verifikační příklad vychází z verifikačního příkladu 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum deflection with consideration of initial slippage.
Verifikační příklad popisuje zatížení větrem v několika směrech proudění větru na modelu skupiny budov. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Jednovrstvá čtvercová ortotropní deska je ve svém středu zcela fixována a namáhána tlakem. Porovnejte průhyby rohů desek pro kontrolu správnosti transformace.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. Je prostě podepřený. The problem is described using the following parameters. Determine the deflections in the given test times.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Self-weight is not considered. Considering an infinitely rigid beam, determine the maximum radial deflection.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Ocelový nosník se čtvercovým průřezem je zatížen normálovou silou a spojitým zatížením. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Hmotový systém s vůlí a dvěma pružinami se nejdříve vychýlí. Determine the natural oscillations of the system - deflection, velocity, and acceleration time course.
Silnostěnná nádoba je zatížena vnitřním tlakem tak, že nádoba dosáhne pružno-plastického stavu. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
Konzola je plně fixována na levém konci a zatížena příčnou silou a normálovou silou na pravém konci. The tensile strength is zero and the behavior in the compression remains elastic.
Ocelové lano nebo membrána s kolíky na obou koncích jsou zatíženy rovnoměrným zatížením. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
Dvouvrstvá silnostěnná nádoba s otevřeným koncem je zatížena vnitřním a vnějším tlakem; proto nevzniká žádné osové napětí. While neglecting self‑weight, the radial deflection of the inner and outer radius, and the pressure (radial stress) in the middle radius is determined.
A cantilever of rectangular cross‑section has a mass at the end. Kromě toho je zatížena normálovou silou. Calculate the natural frequency of the structure. Neglect the self‑weight of the cantilever and consider the influence of the axial force for the stiffness modification.
Konzola z kruhového prutu je zatížena excentrickým rovnoměrným zatížením. Determine the maximum deflection and maximum twist of the console using the geometrically linear analysis.
Uvažujme prostý nosníku ASTM A992 W 18x50 s vlastní tíhou a spojitým užitným zatížením, jak je znázorněno na obrázku 1. Maximální jmenovitá výška prutu je 18 palců. Průhyb při užitném zatížení je omezen na L/360. Nosník je prostě podepřen a spojitě ztužen. Ověřte dostupnou pevnost v ohybu vybraného nosníku na základě LRFD a ASD.
Na obrázku 1 je znázorněn nosník ASTM A992 W 24×62 se smykem na konci 48 000 a 145 000 kips od vlastní tíhy a užitného zatížení. Verify the available shear strength of the selected beam, based on LRFD and ASD.
Stanovte maximální průhyby bloku se zohledněním nebo zanedbáním smykového účinku. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.
A membrane is stretched by means of isotropic prestress between two radii of two concentric cylinders not lying in a plane parallel to the vertical axis. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. K tomu slouží přídavný modul RF-FORM-FINDING. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Spřažená deska sestávající ze tří skleněných vrstev, jedné vrstvy fólie a vnitřního prostoru se suchým vzduchem je plně upevněna a zatížena proměnnou teplotou. Neglecting its self-weight, determine the plate's maximum deflection.
Tlumený jednohmotový systém je zatížen konstantní silou. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Stanoví se přípustná pevnost v osovém tlaku kloubového nosníku o délce 2,8 m různých průřezů ze slitiny 6061-T6 a bočně vetknutého proti vybočení okolo nejslabší osy podle Aluminum Design Manual 2020.
Stanoví se maximální průhyb a napětí ve směru z spřažené desky, která se skládá ze dvou skleněných vrstev a jedné vrstvy fólie mezi nimi a je vystavena konstantnímu tlaku.
A compact disc (CD) rotates at a speed of 10,000 rpm. Je tak vystaven odstředivé síle. The problem is modeled as a quarter model. Determine the tangential stress on the inner and outer diameters and the radial deflection of the outer radius.
Determine the maximum deflection of a three-dimensional block fixed at both ends. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. Na rovinu procházející středem bloku působí svislý tlak.