Konzola obdélníkového průřezu leží na pružném Winklerově podloží a je zatížena rovnoměrným zatížením. The image shows the calculation of the maximum deflection and maximum bending moment.
Ocelový nosník se čtvercovým průřezem je zatížen normálovou silou a spojitým zatížením. The image shows the calculation of the maximum bending deflection and critical load factor according to the second-order analysis.
Osově zatížený ocelový nosník se čtvercovým průřezem je na jednom konci kloubově uložený a na druhém pružně podepřený. Two cases with different spring stiffnesses are considered. The verification example solves the calculation of the load factors of the beam in the image using the linear stability analysis.
Ve spodní části jsou upevněny čtyři sloupy, které jsou nahoře spojeny tuhým blokem. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Ocelové lano nebo membrána s kolíky na obou koncích jsou zatíženy rovnoměrným zatížením. Neglecting its self-weight, determine the maximum deflection of the structure using the large deformation analysis.
A vertical cantilever with a square cross-section is loaded at the top by tensile pressure. Konzola je z izotropního materiálu. Calculate the deflection.
Konstrukce se skládá ze dvou nosníků, které jsou uloženy na kloubových podporách. The structure is loaded by concentrated force. The self-weight is neglected. Determine the relationship between the loading force and the deflection, considering large deformations.
A structure made of I-profile trusses is supported on both ends by spring sliding supports and loaded by transversal forces. Vlastní tíha se v tomto příkladu nezohledňuje. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Vlastní tíhu zanedbáme. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Konzola z obdélníkového průřezu leží na pružném Pasternakově podloží a je zatížena rovnoměrným zatížením. The image shows the calculation of the maximum deflection and maximum bending moment.
Zděná stěna je vystavena rovnoměrnému zatížení uprostřed své horní části. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Konstrukce se skládá ze dvou nosníků různé délky, které jsou uloženy na kloubových podporách. The structure is loaded by concentrated force. The self-weight is neglected. Determine the relationship between the loading force and the deflection, considering large deformations.
A structure made of an I-profile is fully fixed on the left end and embedded into the sliding support on the right end. Konstrukce se skládá ze dvou segmentů. The self-weight is neglected in this example. Determine the maximum deflection of the structure, the bending moment on the fixed end, the rotation of segment 2, and the reaction force at point B by means of the geometrically linear analysis and the second-order analysis. The verification example is based on the example introduced by Gensichen and Lumpe.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum deflection with consideration of initial slippage.
Uvažujeme tuhou lešenářskou trubku, která je ve spodní části fixně podepřena uzlovou podporou pro lešení a zatížena momentem i silou. Calculate the maximum radial deflection by exceeding the capacity of the scaffolding support.
Časová analýza konzoly (SDOF - systém s jedním stupněm volnosti), která je buzena periodickou funkcí. Vertical deformations and accelerations calculated with direct integration and modal analysis in RF‑/DYNAM Pro - Forced Vibrations are compared with the analytical solution.
Tento příklad slouží jako ukázka vazby diafragma. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.