Kelvin-Voigtův materiálový model se skládá z paralelně zapojené lineární pružiny a viskózního tlumiče. V tomto verifikačním příkladu je testováno časové chování tohoto modelu při zatížení a relaxaci v časovém intervalu 24 hodin. Konstantní síla Fx působí po dobu 12 hodin a zbývajících 12 hodin je materiálový model bez zatížení (relaxace). Vyhodnocuje se deformace po 12 a 20 hodinách. Je použita časová analýza s lineární implicitní Newmarkovou metodou.
Dostupné normy, jako například EN 1991-1-4 [1], ASCE/SEI 7-16 a NBC 2015, uvádějí parametry zatížení větrem, jako je součinitel tlaku větru (Cp ) pro základní tvary. Důležité je, jak rychleji a přesněji spočítat parametry zatížení větrem, než pracovat na časově náročných a někdy komplikovaných vzorcích v normách.
Verifikační příklad popisuje zatížení větrem v několika směrech proudění větru na modelu skupiny budov. The model consists of eight cubes. The velocity fields obtained by the RWIND simulation are compared with the measured values from the experiment. The experimental data are measured using a thermistor anemometer in the wind tunnel.
Verifikační příklad popisuje tlaková zatížení na stěny budov v tandemovém uspořádání na úrovni terénu. The buildings are simplified to rectangular objects and scaled down while maintaining the elevation ratios. The pressure distribution on the walls of the model of a medium-high building was conducted by an experiment. The chosen results (pressure coefficient Cp) are compared with the measured values.
Verifikační příklad popisuje ustálené proudění okolo osamělé budovy (zmenšený model).Příklad je uveden od AIJ (Architectural Institute of Japan). The chosen results (velocity magnitude) are compared with the measured values.
A sphere is subjected to a uniform flow of viscous fluid. The velocity of the fluid is considered at infinity. The goal is to determine the drag force. The parameters of the problem are set so that the Reynolds number is small and the radius of the sphere is also small, thus the theoretical solution can be reached - Stokes flow (G. G. Stokes 1851).
A membrane is stretched by means of isotropic prestress between two radii of two concentric cylinders not lying in a plane parallel to the vertical axis. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. K tomu slouží přídavný modul RF-FORM-FINDING. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
Silnostěnná nádoba je zatížena vnitřním tlakem tak, že nádoba dosáhne pružno-plastického stavu. While neglecting self‑weight, the analytical and numerical solutions for the radial position of the plastic zone border (under the Tresca hypothesis) are determined and compared.
Zděná stěna je vystavena rovnoměrnému zatížení uprostřed své horní části. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Konzola je na pravém konci zatížena příčnou a normálovou silou a na levém konci je plně fixována. The problem is described by the following set of parameters. The problem is solved by using the geometrically linear analysis, second-order analysis, and large deformation analysis.
A long, thin beam is carrying a concentrated mass and is loaded by a time-dependent force. Je prostě podepřený. The problem is described using the following parameters. Determine the deflections in the given test times.
Časová analýza konzoly (SDOF - systém s jedním stupněm volnosti), která je buzena periodickou funkcí. Vertical deformations and accelerations calculated with direct integration and modal analysis in RF‑/DYNAM Pro - Forced Vibrations are compared with the analytical solution.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Plastická plocha je popsána podle teorie plasticity Tsai-Wu.
A cantilever beam with an I-beam cross-section of length L is defined. The beam has five mass points with masses m acting in the X-direction. Vlastní tíhu zanedbáme. The frequencies, mode shapes, and equivalent loads of this 5-DOF system are analytically calculated and compared with the results from RSTAB and RFEM.
Stanovíme maximální průhyb čtyř dolních sloupů spojených tuhým blokem nahoře. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
A timber beam reinforced by two steel plates at the ends is loaded by pressure. The wood fibers are parallel to the upper loaded side of the beam. Plastická plocha je popsána podle teorie plasticity Tsai-Wu.