Konstrukce z I-profilu je vetknuta do vidlic. The axial rotation is restricted on both ends while warping is enabled. The structure is loaded by two transverse forces in the middle. The verification example is based on the example introduced by Gensichen and Lumpe.
Rovinný příhradový vazník, který se skládá ze čtyř šikmých prutů a jednoho svislého prutu, je zatížen v horním uzlu svislou silou a silou mimo rovinu. Assuming the large deformation analysis and neglecting the self-weight, determine the normal forces of the members and the out-of-plane displacement of the upper node.
A membrane is stretched by means of isotropic prestress between two radii of two concentric cylinders not lying in a plane parallel to the vertical axis. Find the final minimum shape of the membrane - the helicoid - and determine the surface area of the resulting membrane. K tomu slouží přídavný modul RF-FORM-FINDING. Elastic deformations are neglected both in RF-FORM-FINDING and in the analytical solution; self-weight is also neglected in this example.
A pipe with a tubular cross-section is loaded by internal pressure. This internal pressure causes axial deformation of the pipe (the Bourdon effect). Stanovte axiální deformaci koncového bodu trubky.
Tlumený jednohmotový systém je zatížen konstantní silou. Determine the spring force, damping force, and inertial force at the given test time. In this verification example, the Kelvin--Voigt dashpot (namely, a spring and a damper element in serial connection) is decomposed into its purely viscous and purely elastic parts, in order to better evaluate the reaction forces.
Zakřivený nosník se skládá ze dvou nosníků obdélníkového průřezu. The horizontal beam is loaded by distributed loading. While neglecting self-weight, determine the maximum stress on the top surface of the horizontal beam.
Jednoduchý oscilátor se skládá z tělesa o hmotnosti m (uvažuje se pouze ve směru osy x) a lineární pružiny s tuhostí k . The mass is embedded on a surface with Coulomb friction and is loaded by constant-in-time axial and transverse forces.
Ocelový prut mezi dvěma tuhými podporami se spárou na jednom konci je zatížen rozdílem teplot. While neglecting self‑weight, determine the total deformation of the rod and its internal axial force.
Dvoupodlažní rámová konstrukce o jednom poli je vystavena seizmickému zatížení. The modulus of elasticity and cross‑section of the frame beams are much larger than those of the columns, so the beams can be considered rigid. The elastic response spectrum is given by the standard SIA 261/1:2003. Neglecting self-weight and assuming the lumped masses are at the floor levels, determine the natural frequencies of the structure. For each frequency obtained, specify the standardized displacements of the floors as well as equivalent forces generated using the elastic response spectrum according to the standard SIA 261/1.2003.
Tento příklad slouží jako ukázka vazby diafragma. The application is shown on a two-story structure. The structure is loaded by means of lateral forces according to Figure 1. Determine the maximum deflection of the structure ux in the direction of the loading forces using both the diaphragm constraint and the plate model of the floor.
Zděná stěna je vystavena rovnoměrnému zatížení uprostřed své horní části. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
A structure made of I-profile trusses is supported on both ends by spring sliding supports and loaded by transversal forces. Vlastní tíha se v tomto příkladu nezohledňuje. Determine the deflection of the structure, the bending moment, the normal force in the given test points, and the horizontal deflection of the spring supports.
Na obou koncích je upevněn trojrozměrný blok z elasticko-plastického materiálu. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai-Wu plasticity theory.
Determine the maximum deflection of a three-dimensional block fixed at both ends. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. Na rovinu procházející středem bloku působí svislý tlak.
Na obou koncích je upevněn trojrozměrný blok z elasticko-plastického materiálu s vytvrzením. The block's middle plane is subjected to a pressure load. The surface plasticity is described according to the Tsai‑Wu plasticity theory.
Dokažte, že spojení různých rozměrových prvků nemá vliv na výsledky. A cantilever with a rectangular cross-section is fixed at one end and loaded at the other by concentrated forces. Neglecting its self-weight and assuming only small deformations, determine the cantilever's maximum deflections.