Sadnutí tuhého čtvercového základu na jezerním jílu [1] se spočítá v programu RFEM. Vymodelována je čtvrtina základu. Šířka základů je 75,0 m na obou stranách. Pro generování výsledků se používají fáze výstavby.
Na jedné straně je upevněna tenká deska a na druhé straně je zatížena rovnoměrným momentem. Nejdříve modelujeme desku jako rovinnou desku. Kromě toho je deska modelována jako jedna čtvrtina válcové plochy. Šířka rovinného modelu se rovná délce jedné čtvrtiny obvodu zakřiveného modelu. Zakřivený model tak má téměř stejnou torzní konstantu jako rovinný model.
Stanovte prvních šestnáct vlastních frekvencí dvojitého kříže se čtvercovým průřezem. Každé z osmi ramen je modelováno pomocí čtyř nosníkových prvků a má na konci čepovou podporu (průhyby x a y jsou omezené). Kmitání se zohledňuje pouze v rovině xy. Problém je definován podle normy NAFEMS Benchmarks.
Tento verifikační příklad vychází z verifikačního příkladu 0122. A single-mass system without damping is subjected to an axial loading force. An ideal elastic-plastic material with characteristics is assumed. Determine the time course of the end-point deflection, velocity, and acceleration.
A column is composed of a concrete section (rectangle 100/200) and a steel section (profile I 200). Je vystaven tlakové síle. Determine the critical load and corresponding load factor. The theoretical solution is based on the buckling of a simple beam. In this case, two regions have to be taken into account due to different moments of inertia and material properties.
Kloubový nosník s obdélníkovým průřezem je namáhán rovnoměrným zatížením a vykazuje posun ve svislém směru vlivem excentricity. Considering the small deformation theory, neglecting the self‑weight, and assuming that the beam is made of isotropic elastic material, determine the maximum deflection.
Zděná stěna je vystavena rovnoměrnému zatížení uprostřed své horní části. The Isotropic Masonry 2D material model is compared with the Isotropic Linear Elastic model, with surface stiffness property Without Tension in the nonlinear calculation.
Ve spodní části jsou upevněny čtyři sloupy, které jsou nahoře spojeny tuhým blokem. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled by linear elastic material and the inner columns by a stress-strain diagram with decaying dependence. Assuming only the small deformation theory and neglecting the structure's self-weight, determine its maximum deflection.
Představme si spojení dvou trubek lešení, které je namáháno normálovou silou a momentem. Self-weight is not considered. The material of the tube is idealized as perfectly rigid. All geometrical non-linearities are ignored. Determine the angle of deflection.
Determine the maximum deflection of a three-dimensional block fixed at both ends. The block is divided in the middle: the upper half is made of an elastic material and the lower part is made of timber - an elasto-plastic othotropic material with the yield surface described according to the Tsai-Wu plasticity theory. Na rovinu procházející středem bloku působí svislý tlak.
Stanovíme maximální průhyb čtyř dolních sloupů spojených tuhým blokem nahoře. The block is loaded by pressure and modeled by an elastic material with a high modulus of elasticity. The outer columns are modeled as orthotropic elastic material, and the inner columns as orthotropic elastic-plastic material with the same elastic parameters as the outer columns and plasticity properties defined according to the Tsai-Wu plasticity theory.
Stanovte maximální průhyby bloku se zohledněním nebo zanedbáním smykového účinku. The square block of the isotropic material is fully fixed at one end and loaded with uniform vertical pressure.