Automatic Reinforcement Design

Helpful Questions & Answers

  • Frequently Asked Questions (FAQs)

Can the RFEM 6 Concrete Design add-on automatically design member and surface reinforcement?

Answer

In the current state of RFEM 6, the user must manually define the shear and longitudinal reinforcement for both members and surfaces. This is considered the "Provided Reinforcement" within the Concrete Design add-on. The add-on calculation will then determine the "Required Reinforcement" needed from the analysis and further output the "Not Covered Reinforcement". The user must manually apply additional reinforcement if the "Required Reinforcement" is not met. 

It is planned for the future to have an automatic design of the member and surface reinforcement rather than only the manual input option. 

Keywords

Concrete Reinforced concrete Automatic design Required reinforcement Provided reinforcement Not covered reinforcement

Write Comment...

Write Comment...

  • Views 279x
  • Updated 26 January 2022

Contact Us

Contact Dlubal

Unable to find the answer to your question? Contact us via phone, email, chat or forum or send us your question directly through our online form.

Submit Individual Question

+49 9673 9203 0

[email protected]

Online Training | English

RFEM 6 for Students | USA

Online Training 8 June 2022 1:00 PM - 4:00 PM EST

Online Training | English

RFEM 6 for Students | USA

Online Training 8 June 2022 1:00 PM - 4:00 PM EST

Online Training | English

RFEM 6 | Dynamic Analysis and Seismic Design According to EC 8

Online Training 9 June 2022 8:30 AM - 12:30 PM CEST

Online Training | English

Eurocode 5 | Timber Structures According to DIN EN 1995-1-1

Online Training 15 June 2022 8:30 AM - 12:30 PM CEST

Automatic Creation of Load Combinations in RFEM 6

Automatic Creation of Load Combinations in RFEM 6 and RSTAB 9

Webinar 21 June 2022 2:00 PM - 3:00 PM CEST

Online Training | English

Eurocode 2 | Concrete Structures According to DIN EN 1992-1-1

Online Training 12 August 2022 8:30 AM - 12:30 PM CEST

ADM 2020 Aluminum Design in \n RFEM 6

ADM 2020 Aluminum Design in RFEM 6

Webinar 25 May 2022 2:00 PM - 3:00 PM EST

ASCE 7-16 Response Spectrum Analysis in RFEM 6

ASCE 7-16 Response Spectrum Analysis in RFEM 6

Webinar 5 May 2022 2:00 PM - 3:00 PM EST

Webservice & API in RFEM 6

Webservice & API in RFEM 6

Webinar 20 April 2022 2:00 PM - 3:00 PM CEST

Geotechnical Analysis in RFEM 6

Geotechnical Analysis in RFEM 6

Webinar 7 April 2022 2:00 PM - 3:00 PM CEST

Masonry Design Using Finite Element Method in RFEM 6

Masonry Design Using Finite Element Method in RFEM 6

Webinar 31 March 2022 2:00 PM - 3:00 PM CEST

Tensile Membrane Structure Design in RFEM 6

Tensile Membrane Structure Design in RFEM 6

Webinar 17 March 2022 2:00 PM - 3:00 PM EST

Stability and Torsional Warping Analysis in RFEM 6

Stability Analysis and Torsional Warping (7 DOF) in RFEM 6

Webinar 17 March 2022 2:00 PM - 3:00 PM CET

Data Exchange Between Rhino/Grasshopper and RFEM 6

Data Exchange Between Rhino/Grasshopper and RFEM 6

Webinar 10 March 2022 2:00 PM - 3:00 PM CET

Wind Load Generation Based on CFD in RWIND 2

Wind Load Generation Based on CFD in RWIND 2

Webinar 4 March 2022 10:00 AM - 11:00 AM CET

NDS 2018 Timber Member Design \n in RFEM 6

NDS 2018 Timber Member Design in RFEM 6

Webinar 24 February 2022 2:00 PM - 3:00 PM EST

Analysis of Steel Joints Using FE Model in RFEM 6

Analysis of Steel Joints Using FE Model in RFEM 6

Webinar 24 February 2022 2:00 PM - 3:00 PM CET