11x

2023-02-13

Invitation to the Free Webinar | Wind Load Generation Based on CFD in RWIND 2

Title:
Wind Load Generation Based on CFD Simulation in RWIND 2

Date and time:
Thu, Feb 16, 2023 | 02:00 PM - 03:00 PM CET

Webinars provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.

This webinar will provide an introduction to the numerical simulation of wind flows in RWIND 2 and wind load generation in RFEM 6 and RSTAB 9.

After the presentation is complete, you will be able to download the model(s) used in the webinar. This will allow you to independently follow the webinar step by step with the provided model.

More information and registration:

Wind Load Generation Based on CFD in RWIND 2

Do you have any questions?

Events

2024-04-30

Online Training

RFEM 6 | Students | Introduction to Timber Design

2024-05-02

Construction Stages in Membrane Structures with RFEM 6

Webinar

Construction Stages in Membrane Structures with RFEM 6

2024-05-08

Online Training

RFEM 6 | Students | Introduction to Reinforced Concrete Design

2024-05-08

$Cross-Section Modeling and \n Stress Analysis in RSECTION 1$

Webinar

Cross-Section Modeling and Stress Analysis in RSECTION 1

2024-05-15

Online Training

RFEM 6 | Students | Introduction to Steel Design

2024-05-16

Consideration of Construction Stages in RFEM 6

Webinar

Consideration of Construction Stages in RFEM 6

2024-05-23

Most Frequently Asked Questions Answered by Dlubal Support Team

Webinar

Most Frequently Asked Questions Answered by Dlubal Support Team | May 2024

2024-05-29

$Steel Structures in RFEM 6 \n Part 1: Modeling, Load Input$

Webinar

Modeling and Design of Steel Structures in RFEM 6 | Part 1: Modeling, Load Input

2024-06-06

$Steel Structures in RFEM 6 \n Part 2: Combinations, Design, Documentation$

Webinar

Modeling and Design of Steel Structures in RFEM 6 | Part 2: Combinations, Design, Documentation

2024-06-20

Webinar

Most Frequently Asked Questions Answered by Dlubal Support Team | June 2024

2024-10-16

Online Training

RFEM 6 | Students | Introduction to Member Design

2024-10-23

Online Training

RSECTION 1 | Students | Introduction to Strength of Materials

Videos

Event

Webinar | RWIND 2 - Calculating Wind Loads with CFD Simulation

Length: 00:00:00 min

Event

Webinar | RWIND 2 - Wind Simulation in Digital Wind Tunnel

Length: 00:52:41 min

Event

Webinar | RWIND 2 - CFD Wind Simulation

Length: 00:58:32 min

Event

Wind Simulation in RWIND 2: Modeling, Wind Load Generation, and Documentation

Length: 01:01:40 min

FAQ

FAQ 005286 | How can I consider various wind profiles for various wind directions?

Length: 00:01:18 min

Event

Webinar | CFD Wind Simulation with RWIND 2

Length: 01:02:44 min

FAQ

FAQ 005157 | Where can I adjust the settings of my wind simulation in RFEM 6 / RSTAB 9?

Length: 00:00:12 min

FAQ

FAQ 005156 | Is it possible to use load transfer surfaces in RFEM 6 for wind load generation ...

Length: 00:01:20 min

FAQ

FAQ 005114 | How can I open RWIND using the load wizard in RFEM and RSTAB?

Length: 00:01:52 min

Playlist

Models to Download

290x

35x

Steel Silo with Wind Loads | ASCE 7

1985x

66x

Steel Carport with Solar Panels

683x

57x

Steel Canopy with Wind Loads | ASCE 7

188x

10x

Steel Canopy with Wind Loads | ASCE 7

754x

52x

Aluminum Carport | ADM 2020

623x

30x

Aluminum Carport | ADM 2020

Model 004869 | Floor Panels for Multi-Story Structure

43x

Floor panels for multi-storey construction

Model 004864 | Steel Structure Connection | AISC 360-22

94x

12x

Steel Structure Connection | AISC 360-22

62x

10x

Multi-storey building

Knowledge Base Articles

KB 001870 | Static Analysis with Wind Loads from Experimentally Measured Pressures Using RWIND 2 and RFEM 6

When wind-induced surface pressures on a building are available, they can be applied on a structural model in RFEM 6, processed by RWIND 2, and used as wind loads for static analysis in RFEM 6.

KB 001871 | Interpolation Methods for Experimentally Measured Pressures in RWIND 2

RWIND 2 and RFEM 6 can now be used to calculate wind loads from experimentally measured wind pressures on surfaces. Basically, two interpolation methods are available to distribute pressures measured in isolated points across the surfaces. The desired pressure distribution can be achieved using the appropriate method and parameter settings.

RWIND 2 is a program for generating wind loads based on CFD (Computational Fluid Dynamics). The wind flow numerical simulation is generated around any building, including irregular or unique geometry types, to determine the wind loads on surfaces and members. RWIND 2 can be integrated with RFEM/RSTAB for the structural analysis and design or as a stand-alone application.

KB 001880 | Design of Cable Structures in RFEM 6 and RSTAB 9

In this article, you will learn how to model and design cable structures in RFEM 6 or RSTAB 9.

Product Features

Feature 002746 | Application of Wind Loads from Experimentally Determined Pressure Values

If you have experimentally determined surface pressures available for a model, you can apply them to a structural model in RFEM 6, process them in RWIND 2, and use them as wind loads in the structural analysis of RFEM 6.

You can find out how to apply the experimentally determined values in this technical article.

Feature 002649 | Displaying RWIND Results Directly in RFEM 6

You can display the RWIND results directly in the main program. In the Navigator - Results, select the Wind Simulation Analysis result type from the list above.

Currently, the following results are available, which refer to the RWIND computational mesh:

Surface pressure
Surface cp coefficient
Wall distance y+ (steady flow)

Go to Explanatory Video

Use the "Independent mesh preferred" option in the FE mesh settings to create an independent FE mesh for the integrated objects. This allows you to generate a significantly more detailed and precise FE mesh for individual objects that are integrated into one another.