62 Results
View Results:
Sort by:
Question
In compliance with DIN 1054, the allowable contact stress "Sigma_all" has been entered for the soil contact stress analysis. RF‑FOUNDATION Pro requires a "characteristic value" to be entered. How are both approaches of DIN 1054 and EN 1997‑1 compatible?
Question
How do I determine the stiffness center of my structural system?
Bending Design of Block Foundations
How is the static depth d calculated in the bending design of block foundations (calculation as equivalent beams)?
Question
Which theoretical approaches are used in RF‑/FOUNDATION Pro for pocket foundations with rough bucket sides to divide the forces and moments and carry out the reinforcement layout?
Question
Why do the results of members and sets of members differ in the design?
Question
How can I create a curved or arched section?
Question
I would like to calculate a hall frame with loads from a crane runway. It is not quite clear to me what the various action categories denote. Can you explain it to me?
Question
Can I calculate the spring stiffness of a foundation plate in RFEM 5 or RSTAB 8 with RF‑FOUNDATION Pro and apply this in RFEM?
Question
How can I determine loads at particular geographic coordinates in the online service "Snow Load, Wind Speed, and Seismic Load Maps"?
Question
How are the location-specific Geo-Zone Tool data queries calculated for the determination of various building loads?
Question
Is it possible to generate wind loads according to DIN EN 13782 with this program?
Question
How can I design a foundation for lifting loads?
Question
How can I enter the earth covering of a bucket foundation up to 10 cm below the top edge of the bucket in RF‑/FOUNDATION Pro?
Question
How can I find out how the self-weight of a foundation plate or any imposed load on the foundation plate is considered in the design checks?
Question
Why is the load value displayed in the online service "Geo-Zone Tool: Snow Load, Wind Speed, and Seismic Load Maps" different from the value in the corresponding standard in some cases?
Question
Does the program check the lap length of the vertical stirrups of a block foundation with smooth bucket sides?
Question
I have a foundation that is supported by adjoining frost aprons (distorting beam) in one direction (X- or Y-direction). From the determination of internal forces in RFEM, I get the horizontal support forces in the X- and Y-directions. This is correct. However, the foundations in the X-direction are supported due to the ice wall. Is it possible to "switch off" or neglect the support reaction from RFEM for the foundation design in RF‑/FOUNDATION Pro?
Imperfection from Mode Shape
How do I create an imperfection based on a mode shape in RFEM 6?
Question
Why do I have to define a soil profile in FOUNDATION Pro? I have already specified the allowable soil pressure.
Question
Is it possible to perform design for a timber-concrete composite cross-section?
Question
For the foundation design, I need the results (support reactions) of the design situation for "static equilibrium". How do I get them?
AISI Table B4.1-1 Applicability Limits
Does RFEM check the applicability limits of AISI Table B4.1‑1?
Standardized Sections for AISI Design
Which standardized sections are valid for AISI cold-formed steel design in RFEM 6?
Question
How can I create a drilled beam in RFEM?
Question
Can I apply an impact load to the bucket only, instead of to the entire foundation?
Question
In FOUNDATION Pro, I get extremely large foundations of my structure or I have to enter a very high loading to satisfy the design of the highly eccentric loading in the core. What can be the reason?
Question
Which result combinations can I design with the RF‑/JOINTS Pro program, and what should I pay attention to?
Question
Is it correct that the allowable soil pressure has to be entered as the characteristic value in Window 1.1 General Data of FOUNDATION Pro? Will the design value be determined automatically?
Question
Is it also possible to integrate the online service "Snow Load, Wind Speed, and Seismic Load Maps" into external applications?
- 005113
- Timber Design for RFEM 6
- Timber Design for RSTAB 9
-
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Stress-Strain Analysis for RFEM 6
- Stress-Strain Analysis for RSTAB 9
- Steel Joints for RFEM 6
- Timber Structures
- Concrete Structures
- Steel Structures
- Structural Analysis & Design
- Eurocode 2
- Eurocode 3
- Eurocode 5
- Eurocode 9