- Occurred
- Recorded
Free Webinar | Reinforced Concrete Tank Design in RFEM 6 (USA)
This webinar will provide an introduction to reinforced concrete tank analysis and design in RFEM 6.
2023-01-19
|
English (US)
|
2:00 PM - 3:00 PM EST
|
Free
|
2022-09-29 - 2022-09-30
|
|
|
Free
|
- Occurred
- Recorded
Free Webinar | Tensile Membrane Structure Design in RFEM 6 (USA)
This webinar will provide an introduction to tensile membrane structure design in RFEM 6.
2022-03-17
|
English (US)
|
2:00 PM - 3:00 PM EST
|
Free
|
2021-10-14 - 2021-10-15
|
|
|
Free
|
This training will enable you as a student to work efficiently with the FEM structural analysis program RFEM. You will learn important functions and modeling options by means of practical examples. Open questions can be discussed.
The focus of the third part of this online training is mainly on the design of structural components. Therefore, the structural calculations in timber, steel and reinforced concrete will be done using practical examples.
2021-06-15
|
|
2:00 PM - 4:30 PM CEST
|
Free
|
This training will enable you as a student to work efficiently with the FEM structural analysis program RFEM. Using practical examples, you will learn important functions and modeling options. Open questions can be discussed.
The third part of this online training focuses mainly on the design of structural components. Using practical examples, structural calculations in timber, steel and reinforced concrete are described.
2021-06-14
|
|
09:30 - 12:00 CEST
|
Free
|
- Occurred
- Recorded
This webinar demonstrates the aluminum member design workflow according to the Aluminum Design Manual (ADM) 2020 in RFEM.
Webinars provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.
2021-01-19
|
English (US)
|
2:00 PM - 3:00 PM EST
|
Free
|
This training will enable you as a student to work efficiently with the FEM structural analysis program RFEM. You will learn important functions and modeling options by means of practical examples. Open questions can be discussed.
The focus of the third part of this online training is mainly on the design of structural components. Therefore, the structural calculations in timber, steel and reinforced concrete will be done using practical examples.
2020-12-11
|
|
3:00 PM - 6:00 PM CET
|
Free
|
This training will enable you as a student to work efficiently with the FEM structural analysis program RFEM. Using practical examples, you will learn important functions and modeling options. Open questions can be discussed.
The focus of the third part of this online training is mainly on the design of structural components. In this way, the structural calculations in timber, steel and reinforced concrete will be described using practical examples.
2020-12-07
|
|
09:00 - 12:00 CET
|
Free
|
This training will enable you as a student to work efficiently with the FEM structural analysis program RFEM. You will learn important functions and modeling options by means of practical examples. Open questions can be discussed.
The focus of the third part of this online training is mainly on the design of structural components. Therefore, the structural calculations in timber, steel and reinforced concrete will be done using practical examples.
2020-11-30
|
|
9:00 AM - 12:00 PM CET
|
Free
|
This training will enable you as a student to work efficiently with the FEM structural analysis program RFEM. Using practical examples, you will learn important functions and modeling options. Open questions can be discussed.
The focus of the third part of this online training is mainly on the design of structural components. In this way, the structural calculations in timber, steel and reinforced concrete will be described using practical examples.
2020-11-27
|
|
09:00 - 12:00 CET
|
Free
|
2020-10-14 - 2020-10-17
|
|
|
Free
|
- Occurred
- Recorded
This webinar demonstrates the general workflow for tensile membrane structure design in RFEM including CFD wind load analysis utilizing RWIND Simulation.
Webinars provide the opportunity to gain expert knowledge and to ensure you’re getting the most out of your Dlubal programs.
2020-04-08
|
English (US)
|
2:00 PM - 3:00 PM EDT
|
Free
|
- Occurred
- Recorded
Content:
- Overview and features of RFEM and the design add‑on modules
- Modeling, loading, and analysis of a multi‑material structure in RFEM
- Introduction to the design add-on modules RF-STEEL AISC and RF-CONCRETE
- Review of result output and printout report
2019-06-18
|
English (US)
|
|
Free
|
- Occurred
- Recorded
Content:
- Introduction to the RF‑DYNAM Pro add‑on modules
- Natural frequencies and mode shapes calculation
- Response spectrum analysis per ASCE 7-16
- Story drift, story shear, and P-Delta considerations
2019-05-22
|
English (US)
|
|
Free
|
- Occurred
- Recorded
- Direct integration link between Revit and RFEM
- Explore various scenarios of Revit to RFEM import/export
- Round-tripping of updated model between programs
- Useful tips for a more optimized integration
2018-12-12
|
English (US)
|
|
Free
|
- Occurred
- Recorded
Content
- Modeling, loading, and analysis of reinforced concrete slabs in RFEM
- ACI 318-14 strength and serviceability design with the add‑on module RF‑CONCRETE Surfaces
- Explore both automated and user-defined reinforcement areas
- Deflection analysis considering creep/shrinkage with the add‑on module RF‑CONCRETE Deflect
2016-10-27
|
English (US)
|
|
Free
|
- Occurred
- Recorded
Content
2016-09-29
|
English (US)
|
|
Free
|
- Occurred
- Recorded
2015-01-19
|
English
|
|
Free
|